background image

INSTALLATION GENERAL SAFETY MEASURES AND PRODUCT LIMITATIONS 

Temperature  

Probe Mounting

Run the probe into the monitored compartment and locate the sensor in a spot which will typify the average 

ambient temperature. 

Recommended location is in the center of the ceiling

. Fasten the sensor with the provided 

clamp. Make sure sensor and sensor wire are positioned and/or protected so as not to be damaged by products 

or items in the monitored area. (Seal any openings made for passage of the probe wire into the Cooler/Freezer 

on the inside and the outside of the Cooler/Freezer to prevent a pathway for condensation.

Magnetic Contacts 

Mounting

Mounting method will vary depending on the type of contacts utilized. Make sure that the operating gap  

between the magnet part and the switch part of the contacts accurately detects a door open or a door closed 

condition. (The DOOR light is on constantly when the door is open. This light may be utilized to assist in proper 

switch and magnet placement.) NOTE: For compartments with more than one door, multiple sets of contacts, 

wired in series, may be utilized to monitor multiple door’s status.

Mounting the  

75LCT onto the  

enclosure

Mount the 75LCT onto the enclosure with the provided mounting screws. If the 75LCT is mounted onto an  

outdoor type single gang outlet box, route all wiring away from the battery when the 75LCT is inserted. Inspect 

the installation for compliance with electrical code, safety, sealing against moisture and condensation, and test 

to confirm that the Product and installation are operating properly in accordance with these instructions. Periodic 

testing is recommended to ensure continued proper operation.

Resetting the 

75LCT to factory 

defaults

Press and hold reset button for 2 seconds to restore Factory Set Values.

This document contains confidential information. Dissemination, publication, copying, or duplication of this document or software described herein without prior written authorization is strictly prohibited.

kitchenbrains.com

Page 13 of 16

© 2020 Kitchen  Brains

75LCT MULTI-MONITOR  |  

OPERATING MANUAL

Summary of Contents for Modularm 75LCT

















Reviews: