A
B
C
1” (2.5 cm)
A
Check and Adjust the Burners
The burners are tested and factory-set for most efficient
operation. However, variations in gas supply and other
conditions may make minor adjustments to air shutter or low
flame setting necessary. It is recommended that a qualified
person make burner adjustments.
Checking and adjusting the grill burner flames requires
removing the grates and flame tamers.
Burner Flame Characteristics
The flames of the grill burners and side burners (on some
models) should be blue and stable with no excessive noise or
lifting (LP gas flames will have a slightly yellow tip). A yellow
flame indicates not enough air. If flame is noisy or lifts away
from the burner, there is too much air. Some yellow tips on
flames when the burner is set to HIGH setting are acceptable
as long as no carbon or soot deposits appear. The flames
should be approximately 1" (2.5 cm) high.
Check that burners are not blocked by dirt, debris, insect nests,
etc., and clean as necessary. If they are clean, adjust air
shutters as needed.
IMPORTANT:
Before adjusting air shutters, let burners cool
down completely.
To Adjust:
1.
Light grill using information in the “Outdoor Grill Use”
section.
2.
Observe flame to determine which burners need
adjustment and how the flame is acting.
3.
Turn off the valve and wait until grill and burners cool
completely.
4.
Remove grill grates and flame tamers.
5.
Remove the 2 screws and cotter clip that hold the burner in
place. Set the screw and clip aside.
A.
Air shutter adjustment screw
A.
Valve stem
B.
Small flat-blade screwdriver
C.
Pliers
6.
Remove the burner from the grill by lifting the burner out
7.
If flame is yellow (not enough air), turn air shutter
adjustment screw counterclockwise.
If flame is noisy or lifts away from burner (too much air),
turn air shutter adjustment screw clockwise.
Adjustment should be made clockwise or counter
clockwise
from 1/8” (3.2 mm) to ¼” (6.4 mm).
8.
Replace gas burner, sear plates and grates.
9.
Light grill using information in the “Outdoor Grill Use”
section. See “Burner Flame Characteristics”.
Low Flame Adjustment
If flame goes out on the “
L
” setting, the low flame setting must
be adjusted.
1.
Turn off the valve and wait until grill and burners are cool.
2.
Remove grill grates and flame tamers.
3.
Light grill using information in the “Outdoor Grill Use”
section.
4.
Turn burner to its lowest setting.
5.
Remove each control knob for the main burners and side
burner by loosening the setscrew with the hex key.
6.
Hold valve stem with pliers and insert a small flat-blade
screwdriver into the shaft.
7.
Watch the flame and slowly turn the screwdriver
counterclockwise.
8.
Adjust flame to minimum stable flame.
9.
Replace the control knob and turn off the burner.
10. Repeat steps 3 through 9 for each burner if needed.
11. Replace the flame tamers and grates after the burners
have been cooled.
37
Summary of Contents for 720-0826E
