14
6.
Place the burner caps on the appropriate burner bases.
IMPORTANT:
The bottom of the small and medium caps are
different. Do not put the wrong size burner cap on the burner
base. Each round burner cap is marked with an AUX, SR, UR,
or ST to match with a letter on the burner base.
Small cap
(Auxiliary)
Medium cap (Semi
Rapid)
Large cap (Ultra
Rapid)
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
7.
Plug into a grounded 3-prong outlet.
8.
Slide range into final location, making sure the rear leveling
leg slides into the slot of the anti-tip bracket.
Verify Anti-Tip Bracket Is Installed
and Engaged
On Ranges Equipped with a Storage Drawer:
1.
Remove the storage drawer. See the “Storage Drawer”
section.
2.
Use a flashlight to look underneath the bottom of the range.
3.
Visually check that the rear range foot is inserted into the slot
of the anti-tip bracket.
On Ranges Equipped with a Warming Drawer or
Premium Storage Drawer:
1.
Place the outside of your foot against the bottom front of the
warming drawer or premium storage drawer, and grasp the
lower right or left side of the control panel as shown.
NOTE:
If your countertop is mounted with a backsplash, it
may be necessary to grasp the range higher than is shown in
the illustration.
2.
Slowly
attempt
to
tilt
the
range
forward.
If
you
encounter
immediate
resistance,
the
range
foot
is
engaged
in
the
anti-tip
bracket.
3.
If
the
rear
of
the
range
lifts
more
than
1/2
"
(1.3
cm)
off
the
floor
without
resistance,
stop
tilting
the
range
and
lower
it
gently
back
to
the
floor.
The
range
foot
is
not
engaged
in
the
anti-tip
bracket.
IMPORTANT:
If
there
is
a
snapping
or
popping
sound
when
lifting
the
range,
the
range
may
not
be
fully
engaged
in
the
bracket.
Check
to
see
if
there
are
obstructions
keeping
the
range
from
sliding
to
the
wall
or
keeping
the
range
foot
from
sliding
into
the
bracket.
Verify
that
the
bracket
is
held
securely
in
place
by
the
mounting
screws.
4.
Slide
the
range
forward,
and
verify
that
the
anti-tip
bracket
is
securely
attached
to
the
floor
or
wall.
5.
Slide
range
back
so
the
rear
range
foot
is
inserted
into
the
slot
of
the
anti-tip
bracket.
IMPORTANT:
If
the
back
of
the
range
is
more
than
2
"
(5.1
cm)
from
the
mounting
wall,
the
rear
range
foot
may
not
engage
the
bracket.
Slide
the
range
forward
and
determine
if
there
is
an
obstruction
between
the
range
and
the
mounting
wall.
Changes
to
the
gas
supply
must
be
performed
by
a
qualified
service
technician.
If
you
need
assistance
or
service,
refer
to
the
Quick
Start
Guide
for
contact
information.
6.
Repeat steps 1 and 2 to ensure that the range foot is engaged
in
the
anti-tip
bracket.
If
the
rear
of
the
range
lifts
more
than
1/2"
(1.3
cm)
off
the
floor
without
resistance,
the
anti-tip
bracket
may
not
be
installed
correctly.
Do
not
operate
the
range
without
anti-tip
bracket
installed
and
engaged.
If
you
need
assistance
or
service,
refer
to
the
Quick
Start
Guide
for
contact
information.
Summary of Contents for KFGG500EWH
Page 52: ...Remarques 52 ...
Page 53: ...53 Remarques ...
Page 54: ...Remarques 54 ...
Page 55: ...55 Remarques ...
