background image

3

Installation Dimensions

NOTE: The grounded 3 prong outlet must be inside the upper 
cabinet. See “Electrical Requirements” section.

*33" (83.8 cm) is typical for 69" (175.3 cm) installation height. 

Exact dimension may vary depending on type of range/cooktop 
below.

Product Dimensions

Electrical Requirements

Observe all governing codes and ordinances.
Required:

A 120 Volt, 60 Hz, AC only, 15- or 20-amp electrical supply 
with a fuse or circuit breaker.

Recommended:

A time-delay fuse or time-delay circuit breaker.

A separate circuit serving only this microwave oven.

NOTE: The power source for this microwave oven is an inverter, 
and is incompatible with household inverter power supplies.

A. 2" x 4" wall stud
B. Grounded 3 prong outlet

12" (30.5 cm) min.
13" (33.0 cm) max.

36"

(91.4 cm)

min.

A                   B

upper cabinet and 
side cabinet depth

33"

(83.8 cm)

typical*

69" (175.3 cm) min.

18 

¹⁄₄

"

(46.4 cm)

18 

¹⁄₄

"

(46.4 cm)

35 

⁷⁄₈

" (91.1 cm)

15 

¹⁄₂

"

(39.4 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, 
fire, or electrical shock.

WARNING

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■  

For all cord connected appliances:
The microwave oven must be grounded. In the event of 
an electrical short circuit, grounding reduces the risk of 
electric shock by providing an escape wire for the electric 
current. The microwave oven is equipped with a cord 
having a grounding wire with a grounding plug. The plug 
must be plugged into an outlet that is properly installed 
and grounded.

WARNING: 

Improper use of the grounding plug can 

result in a risk of electric shock. Consult a qualified 
electrician or serviceman if the grounding instructions are 
not completely understood, or if doubt exists as to whether 
the microwave oven is properly grounded. 

Do not use an extension cord. If the power supply cord is 
too short, have a qualified electrician or serviceman install 
an outlet near the microwave oven.

Summary of Contents for KHMS2056SSS - ARCHITECT II 36" 2.0 cu. Ft. 1













Reviews: