4
Parts needed
■
1 UL listed or CSA approved,
¹⁄₂
" (12.5 mm) strain relief
■
2 UL listed wire connectors
■
Home power supply cable
■
4 Concrete anchors for
¹⁄₄
" x 4" hex head lag bolts
(for concrete installation)
For vented installations, you will also need:
■
1 Wall or roof cap
■
Metal vent system
For non-vented (recirculating) installations, you will also
need:
■
Chimney Kit Part Number 8212716 (Stainless Steel), 8212717
(White), or 8212718 (Black). See “Assistance or Service”
section to order.
■
Charcoal Filter Kit Part Number 8285507 for non-vented
(recirculating) installations only. See “Assistance or Service”
section to order.
Parts supplied
Remove parts from packages. Check that all parts were included.
■
Hood canopy assembly with ventilator and light bulbs
installed
■
3 Filters
■
Chimney assembly
■
Ceiling template
■
Mounting template
■
Upper chimney cover
■
Lower chimney cover
■
Parts bag containing:
■
Damper
■
4 Wood shelf bolts
■
4 Wood shelf bolt washers
■
4 Wood shelf nuts
■
4 Bolts to attach canopy to chimney
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial rating
plate is located inside the range hood on the rear wall of the
range hood.
Island hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions provide minimum clearance.
Grounded electrical outlet is required. See “Electrical
Requirements” section.
It is recommended that the hood be fastened into solid wood.
The island hood is factory set for venting through the roof or wall.
For non-vented (recirculating) installations see “Non-Vented
(recirculating) Installation - Style 2” in the “Install Chimney
Covers” section.
All openings in ceiling and where island hood will be installed
must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
Vented Installations
Non-Vented (recirculating) Installations
For non-vented (recirculating) installations, optional Recirculating
Chimney Kit Part Number 8212718 (Black), Kit Part Number
8212716 (Stainless Steel) or Kit Part Number 8212717 (White)
must be used. These kits include a new lower chimney cover
(that replaces the lower chimney cover shipped with the island
hood), a charcoal filter and a diverter.
13
³⁄₄
"
(34.9 cm)
12
¹⁄₁₆
"
(30.6 cm)
26
³⁄₈
"
(65.1 cm)
min.
38
¹⁄₂
"
(97.8 cm)
max.
27
¹⁄₂
"
(69.9 cm)
23
⁵⁄₈
"
(60.0 cm)
3
¹⁵⁄₁₆
"
(10.0 cm)
36" (91.4 cm)
13
³⁄₄
"
(34.9 cm)
12
¹⁄₁₆
"
(30.6 cm)
32"
(81.3 cm)
min.
39"
(99.0 cm)
max.
23
⁵⁄₈
"
(60.0 cm)
3
¹⁄₂
"
(8.9 cm)
12
¹⁄₂
"
(31.8 cm)
5"
(12.7 cm)
3
¹⁵⁄₁₆
"
(10.0 cm)
