13
Overlay Series Custom Panels and Handle Kits
Custom overlay panels allow you to blend the exterior of your
refrigerator into the overall kitchen décor, and to use custom
handles for additional design flexibility.
The custom panels must have backer panels attached in order to
mount them to the refrigerator. It is most common to work with
three panels, as shown in the following graphic: a decorative
overlay panel, a
¹
/
₈
" (3.18 mm) spacer panel or spacer strips and
a
¹
/
₄
" (6.35 mm) backer panel.
In some cases, your cabinet manufacturer may choose to work
with one panel routed for the different dimensions. Follow these
panel dimension and placement instructions to be sure that the
custom overlay panels will fit properly.
IMPORTANT:
■
The weight of the refrigerator door overlay panel cannot
exceed 50 lbs (23 kg).
■
The weight of the freezer door overlay panel cannot exceed
40 lbs (18.1 kg).
■
The weight of the top grille overlay panel cannot exceed
10 lbs (4.5 kg).
To minimize panel weight, you may use 2" (5.08 cm) spacer strips
around the perimeter in place of full-sheet solid spacer panels.
The spacer strips must be set in at least 1" (2.54 cm) from the
top, bottom and sides edges of the backer panel. If you use
spacer strips, it is also recommended that you use two 2"
(5.08 cm) strips horizontally centered for added support.
NOTE: For the grille and the door panels to be flush, the overlay
door panel should be
¹⁄₄
" (6.35 mm) thicker than the overlay grille
panel.
Overlay Panel
Spacer Panel
Backer Panel
5
/
8
" to
3
/
4
"
(15.88 to
19.05 mm)
1
/
8
"
(3.18 mm)
1
/
4
"
(6.35 mm)
1" minimum
(2.54 cm)
Door/Grille Trim
Spacer Panel
Offset Dimension
1
/
8
"
(3.18 mm)
Decorative Overlay Panels
Backer Panels
Model
A
B
C
Model
D
E
F
36
14
³
/
₄
" (37.47 cm)
19
³
/
₄
" (50.17 cm)
34
³
/
₄
" (88.27 cm)
36
14
¹
/
₄
" (36.20 cm) 19
¹
/
₄
" (48.90 cm)
34
³
/
₄
" (88.27 cm)
42
17
¹
/
₄
" (43.82 cm)
23
¹
/
₄
" (59.06 cm)
40
³
/
₄
" (103.51 cm)
42
16
³
/
₄
" (42.55 cm) 22
³
/
₄
" (57.79 cm)
40
³
/
₄
" (103.51 cm)
48
19
³
/
₄
" (50.17 cm)
26
³
/
₄
" (67.95 cm)
46
³
/
₄
" (118.75 cm)
48
19
¹
/
₄
" (48.90 cm) 26
¹
/
₄
" (66.68 cm)
46
³
/
₄
" (118.75 cm)
Bottom Offset
¹⁄₈
" (3.2 mm)
Bottom Offset
¹⁄₈
" (3.2 mm)
14
¹⁄₄
"
(36.2 cm)
33
⁷⁄₈
"
(86.0 cm)
B
A
A
Freezer
Door Panel
(Non-Dispenser)
Refrigerator
Door Panel
C
D
D
E
D
F
7
¹⁄₄
"
(18.4 cm)
6
³⁄₁₆
"
(15.7 cm)
Side Offset
¹⁄₄
" (6.4 mm)
10
⁷⁄₈
"
(27.6 cm)
Preferred
Radius
¹⁄₂
"
(1.27 cm)
72
¹⁄₄
"
(183.5 cm)
Freezer
Door Panel
(Dispenser)
Top Offset
1
⁵⁄₈
" (4.13 cm)
Bottom Offset
¹⁄₂
" (1.27 cm)
22"
(55.9 cm)
33
¹⁄₄
"
(84.5 cm)
70
¹⁄₂
"
(179.1 cm)
70
¹⁄₂
"
(179.1 cm)
Handle-
Side Offset
¹⁄₄
"
(6.4 mm)
Dispenser
cut-out is
centered
left-to-right
