8
16.
Mark centers of the fastener locations through the template
to the wall and to the cabinet.
17.
Remove the template.
NOTE:
The screws provided for mounting this range hood must
be fastened into solid wood; do not fasten into sheet rock only.
Complete Preparation
1.
Determine and make all necessary cuts in the wall or roof for
the vent system. Install the vent system before installing the
range hood. See the “Venting Requirements” section.
2.
Determine the location where the power supply cable will be
run through the wall.
3.
Drill a 1¹
⁄
4
" (3.2 cm) hole at this location.
4.
Pull enough power supply cable through the wall to allow for
easy connection to the terminal box.
5.
Install the 10" (25.4 cm) square x 10" (25.4 cm) round vent
transition with damper to top or rear of the range hood
(depending on your installation), using 4 - 3.5 x 9.5 mm
screws. Remove the damper from the vent transition when
mounting to the rear of the range hood.
NOTE:
There is a 8¾" (22.2 cm)
fl
at cover plate mounted on
the rear panel of the range hood. It must cover the exhaust
opening in the rear panel of the range hood for top venting or
be removed and reinstalled to cover the exhaust opening in
the top panel for rear venting.
6.
Remove terminal box cover and set aside.
7.
Remove knockout from the back of the range hood and
install a UL listed or CSA approved 1/2" (1.3 cm) strain relief.
8.
Place the range hood near its mounting position and run the
power supply cable through the strain relief into terminal box
(enough to make connection).
9.
Tighten the strain relief screws.
NOTE:
Your range hood requires you to purchase either an
internal type or an in-line (external type) blower motor system.
For internal blower systems, there are blower motor mounting
parts in the blower motor installation packet that must be added
to the range hood prior to mounting the range hood to the wall.
See the “Install Range Hood Internal Blower Motor” section and
the instructions supplied with the blower motor.
Install Range Hood
The range hood attaches to the wall by the 2 mounting screws
in the wood support mounted to the wall in the “Range Hood
Mounting Screws Installation” section.
1.
Using 2 or more people, hang the range hood on the the wall
by placing the slotted holes in the range hood back over the
2 screws mounted to the wood support mounted to the wall.
NOTE:
If your installation uses the optional duct cover, the vent
system needs to be connected to the range hood and the duct
cover mounted to the top of the range hood before tightening
the mounting screws. See steps 3-5.
2.
Push the range hood up into the narrow slots, align the
bottom of the hood to the horizontal line, level the hood, and
tighten the 2 mounting screws.
3.
Mark 2 lower mounting hole center point locations. Drill
1/8" (3.2 mm) pilot holes if the holes are located into wood. If
holes are not located into wood, drill two 3/8" (9.5 mm) pilot
holes and insert 10 x 50 mm wall anchors. Install
2 - 6 x 80 mm screws with D5.3 x 20 mm washers into the
lower mounting anchors and tighten.
4.
Install 4 - 4.2 x 19 mm screws through the back of the hood
into the wood support and tighten.
5.
Connect vent system to hood. Seal all joints with clamps.
NOTE:
If your installation uses the optional full-width duct cover,
attach the duct cover to the top of the range hood following the
instructions and using the screws that are provided with the duct
cover.
Install Range Hood Internal Blower
Motor
NOTE:
Your range hood requires you to purchase either an
internal type or an in-line (external type) blower motor system.
The internal blower system can be mounted for top venting or
rear venting. For top venting, the mounting bracket and spring
clip that comes with the blower system will mount to the top
panel of the range hood. For rear venting, the mounting bracket
and spring clip that comes with the blower system will mount to
the rear panel of the range hood.
Prepare the Internal Blower System
IMPORTANT:
Perform steps 1-4 before mounting the range
hood.
1.
Remove grease
fi
lters from range hood. See the “Range
Hood Care” section in the Use and Care Guide.
2.
Install the motor support bracket using three 4.2 x 8 mm
screws. Screw bracket to the inside top or back (alternate
location on some models), toward the left side of the range
hood.
B
CABINE
T’S R
EAR
ARRIÈ
RE DU CABI
NET
PARTE TRA
SERA
DEL GA
BINET
E
DIM0169839
B. Vertical centerline
o
o
