1. Select a dry, level site and clear any sharp objects that may puncture the
floor. Remove the tent from its carry bag, untie fabric ties and unroll the
tent.
2. Take the frame parts bag and carefully tip out the poles. Group the poles
together in to the following pole groups:
Outer Room Poles:
Parts: #71A, #71B (2 Sets)
Inner Room Poles:
Parts: #73A, #73B (2 Sets)
Cantre Ridge Pole:
Parts: #75A, #75B (1 Set)
Leg Support Poles:
Parts: #70A, #70B (4 Sets)
Parts: #72A, #72B, #72C (4 Sets)
Centre Ridge Upright Poles:
Parts: #74A, #74B, #74C (2 Sets)
Porch Poles:
Parts: #76A, #76B, #76C (1 Set)
Parts:
#77A,
#77B
(2
Sets)
Parts:
#78A,
#78B
(2
Sets)
Parts: #79A, #79B, 79C (1 Set)
3. Spread the tent out and move it
into the desired position. Ensure
each side is pulled taut. Peg the
four corners out first, then the
middle pegging loops on each
side, then proceed to peg out
the remaining pegging points.
4. Assemble the Outer Room Poles (Parts #71A, #71 B) by interlocking the
poles. One at a time, feed these through the outer pole sleeves.
5. Assemble the Inner Room Poles (Parts #73A, #73B) by interlocking the
poles. One at a time, feed these through the inner room pole sleeves.
These poles will need to go through the elasticised gusset socks (looks
like a sleeve) on the porch side of the tent.
Moa 10 Frame Tent
Model No. KC070-240
Your tent includes:
1 x Frame Set
1 x Canvas
1 x Canvas Fly (11 x guy ropes attached)
46 x Pegs
5 x Ropes (3 x single ropes, 2 x ‘V’ ropes)
PITCHING INSTRUCTIONS
The poles are coded with a number on a coloured sticker for easier assembly.
The green poles are along the bottom (green for grass), the blue poles are the
upper level poles (blue for sky) and the red poles are the porch poles.
Although the stickers should last well, it is a good idea to label the poles
with the same coloured insulation tape and a permanent marker for future
reference.
To keep the porch clean and out of
the way, fold it back over the roof of
the tent until needed.
To make sure the tent stays in place
insert the pegs into the ground at a
45° angle, not straight down.
6. Assemble the Centre Ridge Pole (Parts #75A,
75B). From the porch side of the tent, insert
the Centre Ridge Pole through the elasticised
gusset sock and then through the pole sleeve
along the centre of the tent, towards the rear
of the tent. Check that all poles have been
threaded through any webbing loops. Also
check that the pole sleeve hasn’t caught when
the poles have been pushed together.
7. Fitting the fly: carefully lay the fly on top of the tent and attach the Velcro
loops to the corners of the tent frame. Clip the buckle into place on at the
front.
8. Assemble the Leg Support Poles (parts #70A, #70B [connected] and
#72A, #72B [connected], 72C)
9. While the tent is still lying on the ground, insert the Inner Leg Support
Poles {Parts #72A, #72B, #72C} through the gusset sock and connect
to the Inner Room Poles. Connect the Outer Support Leg Poles (Parts
#70A, #70B) to the Outer Room Poles.
10. Start raising the tent by taking the Leg Support Poles of one of the inner
rooms and lift the poles until the legs support the canvas. Repeat this for
the other inner room pole then lift the outer room poles into place.
This will take two people to do safely and effectively.
11. Adjust the pole sleeves and the webbing loops to even the tension on the
fabric and smooth out any bunching. Adjust the legs so the canvas is taut.
12. Assemble the Centre Ridge Support leg Poles (#74A, 74B (connected),
74C) and connect to the Centre Ridge Pole. Lift the poles to support the
roof. Adjust the poles to a suitable height using the dome buttons so that
the ridge pole is level when viewed from the outside and the roof fabric is
taut.
check that the pole sleeve hasn t caught when
the poles have been pushed together.
Fitting the fly: carefully lay the fly on top of the tent
loo s t th
f th
f
Cl
Filename: 3732_KC070-240_Moa-10_Instr.pdf
Dimensions: 400mm W x 240mm H
Colour: Black
Unzip and open all of the doors and windows to make erecting the tent easier.
