background image

 

 

103 rue Louvain Ouest, H2N 1A3, Montreal 

 

USER GUIDE HUB2

 | VERSION 1.3

 

 

2.

 

FCC Statements 

 

 

 

FCC ID: 2ADS4HUB2 

 

§ 15.19 (a)(3) 
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)  This 
device may not  cause harmful interference, and (2) this  device must  accept  any interference received,  including 
interference that may cause undesired operation. 
 
§ 15.21 
Important! Changes or modifications not expressly approved by the party responsible for compliance could void the 
user‘s authority to operate the equipment. 
 
§ 15.105 (b) 
Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in 
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following measures: 
—Reorient or relocate the receiving antenna. 
—Increase the separation between the equipment and receiver. 
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
—Consult the dealer or an experienced radio/TV technician for help. 
 
§ 2.1091 (b) 
For purposes of this section, a mobile device is defined as a transmitting device designed to be used in other than 
fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally 
maintained  between  the  transmitter's  radiating  structure(s)  and  the  body  of  the  user  or  nearby  persons.  In  this 
context, the term “fixed location” means that the device is physically secured at one location and is not able to be 
easily moved to another location. Transmitting devices designed to be used by consumers or workers that can be 
easily re-located, such as wireless devices associated with a personal computer, are considered to be mobile devices 
if they meet the 20 centimeter separation requirement.

 

 
DO NOT operate the transmitter when someone is within 20 cm of the antenna. 

 

 

Summary of Contents for Pixmob HUB2











Reviews: