background image

4

4. How to change mode

Press MODE to select auto, heating or cooling mode: the indicator light on the right side of the
controller will indicate the mode selected.

5. How to set the desired water temperature

1).The unit has a unique temperature controlling system to satisfy any requirement.

Heating Only Mode : (+ 1/ - 1°C ‘‘ from set point ’’ )
In Heating Mode the heat pump will only heat.
It will heat up to 1°C higher than the "Set" Temp. The heat pump will then stop,
but it will continue to monitor the temperature in your pool.
(The filter pump must be running to enable the heat pump to measure the temperature).
When the temperature in the pool is 1°C lower than the "Set" Temp.
the heat pump will start again.

Cooling Only Mode : (+ 2/ - 0°C ‘‘ from set point ’’ )
This works the same way, but will only cool when the temperature exceeds

the cooling "Set" Temp. by 2°C and it will cool down to the "Set" Temp.

Remember that the highest Cooling "Set" Temperature is 37°C.

Auto Mode : (‘‘Automatically Heating Mode or Cooling Mode’’ )
In Auto Mode your heat pump will try to keep your desired pool temperature at all times.
Example :
If you want your pool to be 30°C:
A: If the pool-water is below 29°C the heat pump will start heating.

B: When the temperature reaches 31°C the heat pump will stop.
C: If the temperature in your pool continues to rise, and passes 32°C,

the heat pump will start again, BUT in Cooling Mode, and cool down to 30°C.

D: If now the temperature continues to drop, and it drops below 29°C,

the heat pump will start again, BUT in Heating Mode.

In Auto Mode the heat pump will try to keep the temperature within 2°C higher and 1°C
lower that your "Set" Point.
(Remember that the filter pump has to run in order for the heat pump to work)

2).

How to set using the display controller :

a. First select the desired mode: auto, heating or cooling

b. Regardless if the heat pump is "running" or in "standby" press ▲ or ▼.

The display will show the currently set water temperature of the selected mode with a flashing
number: while it is blinking you can change the water temperature by pressing ▲ or ▼ to the
temperature you want.

(Before you select the desired temperature, make sure you are in the correct mode: Heating /
Cooling / Auto.)

After you see the desired temperature blinking, wait 5 sec. and the temperature is stored.

Summary of Contents for KT10X

















Reviews: