background image

Multiplexer 

3 Multiplexer Hardware 

A8 

 

KLIPPEL Analyzer System 

Page 5 of 16 

 

Multiplexer Hardware 

IN / OUTPUT 

CONNECTORS 

 

 

 

 

 

All signal connectors are at the front of 

the device. There are no active compo-

nents in the signal path. 

LINE version provides full symmetrical 

signal paths. 

SPEAKER version provides four wire con-

nections for each speaker channel. 

RACK MOUNTING 

 

 

 

 

The Multiplexer can be used as desktop 

device or rack mounted. 

19” Rack Mounts can be installed at the 

front or backside.  

Status LEDs and Manual mode switch are 

on both sides of the device. 

MANUAL CONTROL 

 

An Up / Down Switch at  the  front and 

backside allows to control the Multiplexer 

manually. An external manual switch can 

be connected optionally.  

IEPE POWER 

 

IEPE microphone supply is available at the 

BNC multiplexer only. It can be switched 

for bank 1 (channel 1 –  4)  and bank 2 

(channel 5 – 8) separately. 

3.1

 

Control Interfaces 

DIGITAL I/O 

The Digital I/O interface can be connected to the Klippel Production Analyzer or Klippel 

Analyzer 3 hardware or any parallel PC port. The Digital I/O Thru connectors allows to 

daisy chain multiple devices. The connection is made by standardized 25 pin D-Sub 

connectors. The interface is optically decoupled for a stabile operation in rough envi-

ronments. 

The Routing Modes have to be selected at DIP switches at the backside of the device.  

USB 

The USB interface is decoupled for a stabile operation in rough environments. 

DIRECT CONTROL 

The Direct Control interface offers the possibility to control each relay directly. The 

wide control voltage range allows the connection from a wide range of devices. The 

Direct Control interface is optically decoupled for a stabile operation in rough environ-

ments. 

 

Summary of Contents for 2800-101

















Reviews: