background image

 

Klippel R&D System 

Contents  

  I 

Contents 

1

 

KCS-ID Manual ....................................................................................................... 1

 

1.1 

Introduction ........................................................................................................................ 1 

1.2 

System Requirements......................................................................................................... 1 

1.3 

Hardware Setup .................................................................................................................. 2 

1.3.1 

Hardware Connection ............................................................................................... 2 

1.3.2 

Hardware Setup - Routing ......................................................................................... 2 

1.4 

Performing Measurements ................................................................................................ 3 

1.4.1 

Basic Measurement Setup ........................................................................................ 3 

1.4.2 

Additional Options .................................................................................................... 4 

1.4.3 

Limit Parameters ....................................................................................................... 4 

1.4.4 

Running and Interpreting Measurements ................................................................. 5 

1.5 

Creating Initial Data ............................................................................................................ 7 

1.6 

X

max

 and X

target

 ..................................................................................................................... 7 

1.6.1 

Why is X

max

 not equal to X

target

? ................................................................................. 7 

1.6.2 

How to achieve a higher Xmax? ................................................................................ 8 

1.7 

Transducers with multiple voice coils ................................................................................ 9 

1.8 

Troubleshooting ............................................................................................................... 10 

1.8.1 

KCS-ID messages ..................................................................................................... 10 

1.8.2 

KCS Server messages ............................................................................................... 10 

2

 

Index ................................................................................................................... 13

 

 

Summary of Contents for KCS-ID


















Reviews: