background image

BAC-9300 Series Controller Installation Guide 

10 925-019-02G

 © 2019 KMC Controls, Inc. 

Specifications and design subject to change without notice 

925-019-02

G

IMPORTANT NOTICES

The material in this document is for information 

purposes only. The contents and the product it 

describes are subject to change without notice.

KMC Controls, Inc. makes no representations or 

warranties with respect to this document. In no 

event shall KMC Controls, Inc. be liable for any 

damages, direct, or incidental, arising out of or 

related to the use of this document.
The KMC logo is a registered trademark of KMC 

Controls, Inc. All rights reserved.
TEL:  574.831.5250

 

FAX:  574.831.5252

 

EMAIL: 

info@kmccontrols.com

REPLACEMENT PARTS

HPO-0055

 

Replacement Network 

Bulb Module for Conquest 

Controllers, Pack of 5

HPO-9901

 

Conquest Hardware 

Replacement Parts Kit

NOTE: 

HPO-9901 includes the following:

Terminal Blocks   

DIN Clips

(1) Black 2 Position 

(2) Small

(2) Grey 3 Position  

(1) Large

(2) Green 3 Position
(4) Green 4 Position
(2) Green 5 Position
(2) Green 6 Position

NOTE: 

See the 

Conquest Selection Guide

 for 

more information about replacement 

parts and accessories.

Summary of Contents for BAC-9300 Series











Reviews: