background image

0901177 Rev: A  (10/15) 

Page 1 of 12 

UMP Hospitality 

Instruction Manual

 

TABLE OF CONTENTS 

Settings Guide ......................................................................................................  2 

Installation Diagram ..............................................................................................  3 

Dimensions ........................................................................................................... 3 

Accessory Kit ........................................................................................................ 3 

Installation ............................................................................................................ 4 

Electrical ...............................................................................................................  5 

Operation .............................................................................................................. 6 

Programming ........................................................................................................  7 

Parts Diagram ...................................................................................................... 9 

Wiring Diagram ...................................................................................................  10 

Warranty Information ..........................................................................................  12 

Knight Locations .................................................................................................  12 

Summary of Contents for UMP Hospitality













Reviews: