Functions instructions
Door chime operation
Press the push button on the bell push unit once, a wireless signal is sent to the
receiver which will sound. The sound will stop as soon as the melody ends. For
repeated sound, press the button again. Please note, holding the button in will not
repeat the sound.
Melody selection
There is a melody selector located on the back of the door chime on the right.
Press the selector to choose a different melody.
Sound and flash
There is a switch on the back of the receiver on the left. Slide the switch to the left
position: the receiver will work with sound only; slide to the middle position: the LED
will flash only; slide to the right position for sound and LED flash.
Volume adjustment
There is a volume button between the melody selector and the sound-and-flash
switch. Press to adjust the sound volume - high, medium or low.
Auto-learning code button
There is an auto-learning code button under the melody selector. If you want an
additional bell push to work with the receiver, press the auto-learning code button
once and the bell push will work with the receiver (please see detailed operation
‘Auto-learning code set up’ in this manual).
Nameplate
There is a nameplate position on the bell push for user identification. Remove the
nameplate cover and put a suitable sized label with name or required information,
and replace cover (label is not included with this kit).
Important
1. The receiver is designed for indoor use only
2. Do not mount the bell push onto any metal surface or PVCu doorframes, as this
will reduce the operation range
3. Do not expose either unit directly to rain or immerse in water
4. Do not mount either unit close to a fireplace or expose to high temperatures
5. If leaving the door chime for long periods, please remove the battery from
compartment to prevent leakage
6. Please dispose of old batteries in accordance with relevant legislation
Names of parts
2. LED indicator
8. Hanging slot
3. Sound-and-flash switch
9. Push button
4. Battery cover
10. Nameplate cover
5. Volume button
11. Front and back cover hook
6. Melody selector
12. Standby holes for screws
7. Auto learning code button
13. Interface
Notes before installation
1.
Before installation and operation, you will require a drill, cross-head screwdriver,
flat-head screwdriver, 2 × AA 1.5V batteries, fixing screws
and wall plugs. These items are not supplied with this kit
2. Avoid positioning the bell push on metal frames
3. Avoid positioning above heat sources such as radiators, or in damp areas such as
a kitchens or bathrooms
How to use the door chime kit
Pressing the bell push, a wireless signal will be sent to the receiver.
The receiver will be activated and sound. The operating range is 200m (in the open
air) and you can use the receiver virtually anywhere in the home (indoor use only).
However, the transmission range will be reduced if the signal is transmitted through
walls or ceilings. Metal or PVCu doorframes can also reduce the operating range.
Battery installation
Bell push unit
• The bell push uses a 3V CR2032 battery (included)
• Open the bell push by pushing in the interface located at the bottom with a flat-
head screwdriver and insert the battery. Please note the correct battery polarity
Receiver unit
Remove the battery cover and insert 2 x 1.5V AA batteries (not included).
Ensure battery polarity matches the internal markings.
User hints
If the receiver does not sound, please check the following:
• Flat batteries in either bell push or receivers - change the batteries
• Wrong battery polarity in either bell push or receivers - re-insert the
batteries correctly
• Units are out of range - operate the receiver within the recommended
operation range
Specification
Bell push unit
Power:
1×3V CR2032 battery (included)
Receiver unit
Power:
2 x 1.5V AA alkaline batteries (not included)
Operating temperature:
-30 °C (to +400 °C)
Operating distance:
200 meters (in the open air) (265ft approx.- (in the open air and
suitable conditions)
Selectable tone:
Total 36 melodies available
Digital code type:
Auto-learning
What is auto-learning code?
The bell push sends a wireless signal to the receiver. The receiver will automatically
register and memorize the signal as an operation code.
The bell push can work with the receiver by using this code.
Auto-learning code set up
The door chime kit is equipped with auto-learning operation code ability.
1. Operation for 1 bell push and 1 receiver
After battery installation on both bell push and receiver, press the bell push once
to generate a new operation code. The receiver will sound which indicates that a
new operation code is registered and memorized
2. Interference from another door chime operating nearby (for example: receiver
sounds for no reason): remove the batteries from the receiver and rest for 30
seconds. This will erase the memory. Insert the batteries, the bell push and
receiver are ready for the new code registration
3. Operation for the 2nd / 3rd / 4th / 5th bell pushes and the receiver
(there is only 1 bell push included with this kit):
Wall mount
To install, you will require a drill and cross-head screwdriver.
IMPORTANT: Before you drill any hole in the wall, please make sure there are no
cables or pipes that may accidentally be damaged.
Bell push unit
1. Open the bell push with a screwdriver and separate the front cover from the back
cover (as previously described). Penetrate the two standby holes on the back cover
with two screws, then fix the screws onto the wall at a suitable height (see picture 1).
2. Alternatively, you can attach the bell push with double-sided adhesive tape
(see picture 2)
Mounting on PVCu or metal doorframe surfaces will reduce the transmitting range
Receiver unit
Fix a screw onto the wall and hang the receiver by the slot at the back of the unit.
Avoid positioning on PVCu frames, above heat sources (e.g. radiators) or in damp
areas such as a kitchens or bathrooms. Important: test the receiver before drilling
any holes to ensure it is within recommended operating range.
Note: Alternatively, the receiver can also be placed on a flat surface.
(a) Insert the batteries into the bell push, the receiver is ready for the new
code registration
(b) Press the auto-learning code button on the back of the receiver once, and
it will be ready to receive the signal sent from the second bell push. Press the
button of the bell push, the receiver will sound to indicate that new operation
code is registered and memorized. Thus the second bell push works successfully
with the receiver. For the 3rd, 4th, and 5th bell push, please follow the
same procedure
(c) It is important to remember, when you replace dead batteries with new ones,
please follow the auto-learning code set-up procedure as above
NOTES
(a) If the receiver sounds for no reason during the digital code setting, this indicates
interference from another similar door chime nearby. Reset the auto-learning
code (as per point 2 above)
(b) One receiver will work with maximum five bell pushes at the same time. If the
bell push is missing a terminal, the bell push can be purchased separately and
set up using the auto-learning code instructions above
IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
WHEN REPLACING BATTERIES
92
INSTALLATION & MAINTENANCE MANUAL
DC001
It is very important to install and operate this product according to the following
instructions. Failure to do so may render your guarantee void.
Accessories list
The door chime kit comes with:
• 1 x Receiver
• 1 x Bell push
• 1 x 3V CR2032 battery for bell push
• 1 x Double-sided adhesive pad
• 1 x Instruction manual
Pictures for accessories
Names for parts
(1)
(2)
(4)
(3)
(8)
(7)
(6)
(5)
(13)
(12)
(11)
(10)
(9)
Receiver
Receiver front side
Receiver back side
Transmitter front
cover outside
Transmitter back
cover inside
Transmitter
CR2032 battery
Double-sided
adhesive
Instruction
manual
1
2
1
2
Receiver
Battery cover
1.5V AA
Alkaline
batteries
Load batteries and replace cover
1
4
2
5
3
6
DC001_INSTRUCTIONS.indd 1
07/07/2014 14:35
