These instructions should be read carefully and retained after installation by the end user for future
reference and maintenance.
These instructions should be used to aid installation of the following product:
JB0011
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this product should only be carried out by a qualified electrician or competent person
to the current Building and IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Please note the IP (Ingress of Protection) rating of this product when deciding the location for
installation
• This product is suitable for a maximum load of 16A
• This product is IP68 rated
• Connect the Live (brown) – L, Earth (yellow green) - , and Neutral (blue) – N into the connector
plug and connector socket and slide the shell over the terminations and tighten to 2.5Nm
• Slide the seal into the shell and tighten nut to 2.5Nm
• Connect the connector socket and connector plug together and tighten to 2.5Nm
• Switch on power and test for correct operation
3
2
JB0011
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following product:
JB0011
SAFETY
•
Installation of this product should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulations (BS7671)
•
Please isolate mains prior to installation/maintenance
•
Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation
•
This product is Class I and must be earthed
•
This product is suitable for a maximum load of 16A
•
This product is IP68 rated
INSTALLATION
•
Connect the Live (brown) – L, Earth (yellow green) -
, and Neutral (blue) – N into the connector plug and
connector socket and slide the shell over the terminations and tighten to 2.5Nm
•
Slide the seal into the shell and tighten nut to 2.5Nm
Nut
Seal
Sea
l
Lock
nut
Connector socket
Shell
Connector plug
Shell
Nut
JB0011
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following product:
JB0011
SAFETY
•
Installation of this product should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulations (BS7671)
•
Please isolate mains prior to installation/maintenance
•
Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation
•
This product is Class I and must be earthed
•
This product is suitable for a maximum load of 16A
•
This product is IP68 rated
INSTALLATION
•
Connect the Live (brown) – L, Earth (yellow green) -
, and Neutral (blue) – N into the connector plug and
connector socket and slide the shell over the terminations and tighten to 2.5Nm
•
Slide the seal into the shell and tighten nut to 2.5Nm
Nut
Seal
Sea
l
Lock
nut
Connector socket
Shell
Connector plug
Shell
Nut
•
Connect the connector socket and connector plug together and tighten to 2.5Nm
•
Switch on power and test for correct operation
WARNING
Do not use any source of high pressure washers to maintain or clean this product.
GENERAL
The unit should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where
facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the fitting.
We recommend the use of H07RN-F cable with this product.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with the current
edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the warranty. If this
product should fail within its warranty period it should be returned to the place of purchase for a free of charge
replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement
product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior
notice.
Do not use any source of high pressure washers to maintain or clean this product
The unit should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may
damage the fitting.
We recommend the use of H07RN-F cable with this product.
This product has a warranty of 3 years from date of purchase. Failure to install this product in
accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of
the batch codes will invalidate the warranty. If this product should fail within its warranty period it
should be returned to the place of purchase for a free of charge replacement. ML Accessories does
not accept responsibility for any installation costs associated with the replacement product. Your
statutory rights are not affected. ML Accessories reserve the right to alter product specification
without prior notice.
WARNING
GENERAL
WARRANTY
JB0011 INSTRUCTIONS_spreads.indd 2
23/01/2017 10:09
