2
These instructions should be read carefully and retained after installation by the end-user for
future reference and maintenance.
These instructions should be used to aid the installation of the following products:
LDGL5 / LDGL6 / LDGL9
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation
• This product is Class I and must be earthed
• This product series is IP65 rated
Note
- If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires.
• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable
IP rated junction boxes should be used where required
• The power source connections should be local and accessible via a suitable IP rated enclosure
• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1 and Tab. 1) ensuring not
to infringe with any joists, gas/water pipes or electrical cables
• Connect the luminaire to the mains supply ensuring that correct polarity is observed (see Fig. 2):
Live (Brown), Earth (Green/Yellow), Neutral (Blue)
Fig. 1
Tab. 1
LDGLxx INSTRUCTIONS
These instructions should be read carefully and retained after installation by the end-user for future reference and
maintenance.
These instructions should be used to aid the installation of the following products:
LDGL5 / LDGL6 / LDGL9
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating
of the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•
This product is Class I and must be earthed
•
This product series is IP65 rated
INSTALLATION
Note
- If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with
the manufacturer of the sensors that they are compatible with LED luminaires.
•
Provide power to the required point of installation (refer to BS7671 for correct
cabling methods). Suitable IP rated junction boxes should be used where required
•
The power source connections should be local and accessible via a suitable IP rated enclosure
•
Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1 and Tab. 1)
ensuring not to infringe with any joists, gas/water pipes or electrical cables
Fig. 1
Tab. 1
Part Code
Cut-out "A"
With mounting sleeve
(mm)
Without mounting sleeve
(mm)
LDGL5
60
55
LDGL6
114
108
LDGL9
144
138
A
LDGLxx INSTRUCTIONS
These instructions should be read carefully and retained after installation by the end-user for future reference and
maintenance.
These instructions should be used to aid the installation of the following products:
LDGL5 / LDGL6 / LDGL9
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating
of the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•
This product is Class I and must be earthed
•
This product series is IP65 rated
INSTALLATION
Note
- If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with
the manufacturer of the sensors that they are compatible with LED luminaires.
•
Provide power to the required point of installation (refer to BS7671 for correct
cabling methods). Suitable IP rated junction boxes should be used where required
•
The power source connections should be local and accessible via a suitable IP rated enclosure
•
Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1 and Tab. 1)
ensuring not to infringe with any joists, gas/water pipes or electrical cables
Fig. 1
Tab. 1
Part Code
Cut-out "A"
With mounting sleeve
(mm)
Without mounting sleeve
(mm)
LDGL5
60
55
LDGL6
114
108
LDGL9
144
138
A
