Knorr-Bremse MICROENER TEMON 4-C Operation Manual Download

Page: 2 / 14

TEMON 4-C

Doc. N°

MO-0368-ING

2.1

Date

01.12.2008

Rev.

Pag.

1. Generality ______________________________________________________________________________________________________ 3

2. Introduction ____________________________________________________________________________________________________ 3

3. Accessories and Options _________________________________________________________________________________________ 3

4. Installation _____________________________________________________________________________________________________ 3

5. Connection of the Thermometer Sensors ____________________________________________________________________________ 4

6. Output Relays ___________________________________________________________________________________________________ 4

7. Wiring Connection _______________________________________________________________________________________________ 5

8. Description Front Panel

– Operators ________________________________________________________________________________ 6

9. Programming of the Device _______________________________________________________________________________________ 7

9.1 - Selection of the HOLD function __________________________________________________________________________________ 7

9.2 - Selection of the number of active inputs ___________________________________________________________________________ 7

9.3 - Control ventilation ____________________________________________________________________________________________ 8

9.4 - Selection of the threshold of switch on and switch off ventilation ________________________________________________________ 8

9.5 - Selection threshold of disable ventilation __________________________________________________________________________ 8

9.6 - Selection threshold of enable ventilation ___________________________________________________________________________ 8

9.7 - Selection of the alarm and tripped threshold ________________________________________________________________________ 9

9.8 - Selection of address network identification for the communication of the serial port (MODBUS-RTU protocol) ____________________ 9

9.9 - Selection of baud rate _________________________________________________________________________________________ 9

9.10 - Selection data bit, parity and stop bit____________________________________________________________________________ 10

9.11 - Selection of the channel linked to the analogical output _____________________________________________________________ 10

9.12 - Configuration of output signal _________________________________________________________________________________ 10

9.13 - Configuration diagnostic probes _______________________________________________________________________________ 11

9.14 - The exit of the programming phase _____________________________________________________________________________ 11

10. Modality Of Tripping And Restore ________________________________________________________________________________ 12

10.1 - Alarm ____________________________________________________________________________________________________ 12

10.2 - Trip _____________________________________________________________________________________________________ 12

10.3 - To silence alarm ___________________________________________________________________________________________ 12

11. Diagnostic ____________________________________________________________________________________________________ 12

12. Visualization of the Maximum Measured Value of Temperature ________________________________________________________ 13

13. Visualization of the Channels With the Higher Temperature ___________________________________________________________ 13

14. Test of the Light Signalling ______________________________________________________________________________________ 13

15. Visualization of the Measured Temperature ________________________________________________________________________ 13

16. Exclusion of the Probe Inputs Not Used ___________________________________________________________________________ 13

17. Technical Features _____________________________________________________________________________________________ 14

18. Dimensions ___________________________________________________________________________________________________ 14

Summary of Contents for MICROENER TEMON 4-C













Search results

Summary of Contents for MICROENER TEMON 4-C

Reviews:

Related manuals for MICROENER TEMON 4-C

Brands by name

Popular brands

Knorr-Bremse MICROENER TEMON 4-C, Operation Manual

Search results

Summary of Contents for MICROENER TEMON 4-C

Reviews:

Related manuals for MICROENER TEMON 4-C

Brands by name

Popular brands