background image

Ambient temperature 

-5 ... +45 °C 

Storage/transport temperature 

-25 ... +70 °C 

Outputs 
Contact type 

µ contact, monostable 

Switching voltage 

AC 250 V ~ 

Switching current AC1 

16 A 

Fluorescent lamps 

16 AX 

Current carrying capacity 
Neighbouring outputs 

Σ 20 A 

Device 

Art. No. 2304.16 REG HE 

Σ 40 A 

Art. No. 2308.16 REG HE 

Σ 80 A 

Art. No. 2316.16 REG HE 

Σ 160 A 

Loads per output 
Ohmic load 

3000 W 

Capacitive load 

max. 16 A (140µ) 

Motors 

1380 VA 

Switch-on current 200 µs 

max. 800 A 

Switch-on current 20 ms 

max. 165 A 

Lamp loads 
Incandescent lamps 

3000 W 

HV halogen lamps 

2500 W 

LV halogen lamps with Tronic transformer 

1500 W 

LV halogen lamps with inductive transformer 

1200 VA 

Fluorescent lamps T5/T8 
uncompensated 

1000 W 

parallel compensated 

1160 W (140 µF) 

 Duo circuit 

2300 W (140 µF) 

Compact fluorescent lamps 
uncompensated 

1000 W 

parallel compensated 

1160 W (140 µF) 

Mercury vapour lamps 
uncompensated 

1000 W 

parallel compensated 

1160 W (140 µF) 

Connections supply and load 
Connection mode 

Screw terminal 

single stranded 

0.5 ... 4 mm² 

finely stranded without conductor sleeve 

0.5 ... 4 mm² 

finely stranded with conductor sleeve 

0.5 ... 2.5 mm² 

Fitting width 

Art. No. 2304.16 REG HE 

72 mm / 4 modules 

Art. No. 2308.16 REG HE 

72 mm / 4 modules 

Art. No. 2316.16 REG HE 

144 mm / 8 modules 

Weight 

Art. No. 2304.16 REG HE 

approx. 250 g 

Art. No. 2308.16 REG HE 

approx. 290 g 

Art. No. 2316.16 REG HE 

approx. 460 g 

KNX 
KNX medium 

TP 1 

Commissioning mode 

S-mode 

Rated voltage KNX 

DC 21 ... 32 V SELV 

Power consumption KNX 

typical 150 mW 

Connection type for bus 

Connection terminal 

6.2 Troubleshooting 

Manual control with button field not possible 

Cause 1: Manual control has not been programmed. 

Program manual control. 

9/11 

82560023 
J:0082560023 

05.08.2013 

Switch actuator / blinds actuator 

Summary of Contents for Jung 2304.16 REG HE












Reviews: