Kobalt 200-2449, Operator'S Manual

200-2449

3

1.

RISK OF FIRE OR EXPLOSION. Never spray 
flammable liquids in a confined area. It is normal for 
the motor and pressure switch to produce sparks 
while operating. If sparks come into contact with 
vapors from gasoline or other solvents, they may 
ignite, causing fire or explosion. Always operate the 
compressor in a well–ventilated area. Do not smoke 
while spraying. Do not spray where sparks or flame 
are present. Keep compressor as far from spray area 
as possible.

2.

RISK OF BURSTING. Rust can weaken the tank. 
Drain the condensed water from the tank after each 
use to reduce rusting. If a leak is detected in the tank, 
replace the tank immediately. Do not weld, drill or 
modify the air tank of this compressor. Welding or 
modifications on the air compressor tank can severely
impair tank strength and cause an extremely 
hazardous condition. Welding or modifying the tank in 
any manner will void the warranty.

3.

RISK OF ELECTRICAL SHOCK. A licensed

electrician in accordance with all local and national
codes must install all wiring. Never use an electric air
compressor outdoors when it is raining or on a wet
surface, as it may cause an electric shock.

4.

RISK OF INJURY. This unit starts automatically.

ALWAYS shut off the compressor, remove the plug
from the outlet, and bleed all pressure from the
system before servicing the compressor, and when
the compressor is not in use. Do not operate the unit 

with the shroud removed. Serious injury could occur 
from contact with moving parts.

5.

RISK OF BURSTING. Check the manufacturer’s
maximum pressure rating for air tools and
accessories. Compressor outlet pressure must be
regulated so as to never exceed the maximum
pressure rating of the tool. Relieve all pressure 
through the hose before attaching or removing 
accessories.

6.

RISK OF BURNS. High temperatures are generated

by the pump and  manifold. To prevent burns or other
injuries, DO NOT  touch the pump, manifold or
transfer tube while the pump is running. Allow them to
cool before handling or servicing. Keep children away 

from the compressor at all times.

7.

RISK TO BREATHING. Be certain to read all labels
when you are spraying paints or toxic materials, and
follow the safety instructions. Use a respirator mask if
there is a chance of inhaling anything you are
spraying. Read all instructions and be sure that your 
respirator mask will protect you.

8.

RISK OF EYE INJURY. Always wear ANSI Z87.1

approved safety goggles  when using an air
compressor. Never point any nozzle or sprayer toward
a person or any part of the body. Equipment can 

cause serious injury if the spray penetrates the skin.

9.

RISK OF BURSTING. Do not tamper with the control
board or adjust the relief valve for any reason. Doing
so voids all warranties. They have been preset at the
factory for the maximum pressure of this unit.
Personal injury and/or property damage may result if 
the control board or the relief valve are tampered with.

10. RISK OF BURSTING. Do not use plastic or pvc pipe

for compressed air. Use only galvanized steel pipe
and fittings for compressed air distribution lines.

11. RISK TO HEARING. Always wear hearing protection

when using an air compressor. Failure to do so may
result in hearing loss.

12.  RISK TO BREATHING. Never directly inhale the

compressed air produced by a compressor. It is not
suitable for breathing purposes.

13. The power cord on this product contains lead, a 

chemical known to the State of California to cause
cancer, and birth defects or other reproductive harm.
Wash hands after handling.

WARNING

CAUTION

SAFETY GUIDELINES

The following information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this
information, we use the following symbols. Please read the manual and pay attention to these sections.

– A POTENTIAL HAZARD THAT WILL CAUSE SERIOUS INJURY OR LOSS OF LIFE.

– A POTENTIAL HAZARD THAT COULD CAUSE SERIOUS INJURY OR LOSS OF LIFE.

– A POTENTIAL HAZARD THAT MAY CAUSE MODERATE INJURY OR DAMAGE TO EQUIPMENT.

WARNING:

DANGER:

CAUTION:

1.

Drain the moisture from the tank on a daily basis. A 
clean, dry tank will help prevent corrosion.

2.

Pull the pressure relief valve ring daily to ensure that 
the valve is functioning properly, and to clear the 
valve of any possible obstructions.

3.

To provide proper ventilation for cooling, the 
compressor must be kept a minimum of 12 inches (31 
cm) from the nearest wall, in a well–ventilated area.

4.

Fasten the compressor down securely if transporting 
is necessary. Pressure must be released from the 
tank before transporting. 

5.

Protect the air hose and electric cord from damage 
and puncture. Inspect them weekly  for weak or worn 
spots, and replace if  necessary.

6.

To reduce the risk of electric shock, do not expose to 
rain. Store indoors.

7.

Never operate the compressor if the power cord or 
plug are damaged. Take the equipment to the nearest 
Authorized Service Center, and have a Technician 
replace it.