background image

11

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package 

contents list. If any part is missing or damaged, do not attempt to assemble the product.

Helpful Tools: Wrench for tightening the chain and connecting the poles.

UNPACKING

• This product has been shipped unassembled.

• Carefully remove the product and any accessories from the box. Make sure that all items listed in the 

Package Contents list are included.

• Inspect the product carefully to make sure no breakage or damage occurred during shipping.

• Do not discard the packing material until you have carefully inspected and satisfactorily operated the 

product.

• If any parts are damaged or missing, please call 

1-888-3KOBALT

 (1-888-356-2258) for assistance.

 

WARNING

• If any parts are damaged or missing, do not operate this product until the parts are replaced. Failure 

to heed this warning could result in serious personal injury.

• Do not attempt to modify this product or create accessories not recommended for use with this 

product. Any such alteration or modification is misuse and could result in a hazardous condition 

leading to possible serious personal injury.

• Do not install the battery until assembly is complete. Failure to comply could result in accidental 

starting and possible serious personal injury.

Summary of Contents for 2220273


























Reviews: