background image

24

TROUBLESHOOTING

If you still have questions or an unresolved issue after going through this troubleshooting guide, 

or just want to speak to a Kobalt product expert, please call our customer service department at 

1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST, Monday – Sunday.

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

Bar and chain

running hot and

smoking.

1. Check chain tension for 

overtightened condition.

2. Bar lube reservoir empty.

1. Tension chain. Refer to Chain 

Tension earlier in this manual.

2. Check bar lube reservoir.

Motor runs, but

chain is not

rotating.

1. Chain tension too tight.
2. Check guide bar and chain

    assembly.
3. Check guide bar and chain for

    damage.

1. Re-tension chain. Refer to Chain  

Tension earlier in this manual.

2. Refer to Replacing the Bar and 

Chain earlier in this manual.

3.  Inspect guide bar and chain for 

damage.

5-YEAR LIMITED WARRANTY

This Kobalt 80 V Lithium-ion pole saw is warranted to the original purchaser from the original purchase 

date for five (5) years subject to the warranty coverage described herein.

This Kobalt 80 V Lithium-ion pole saw is warranted for the original user to be free from defects in 

material and workmanship.

If you believe that the Kobalt 80 V Lithium-ion pole saw is defective at any time during the specified 

warranty period, simply return the 80 V Lithium-ion pole saw along with proof of purchase to the place 

of purchase for a free replacement or refund or call 1-888-3KOBALT (1-888-356-2258) for warranty 

service.

This warranty is void if: defects in materials or workmanship or damages result from repairs or 

alterations which have been made or attempted by others or the unauthorized use of nonconforming 

parts; the damage is due to normal wear, damage is due to abuse (including overloading of the tool 

beyond capacity), improper maintenance, neglect or accident; or the damage is due to the use of the 

tool after partial failure or use with improper accessories or unauthorized repair or alteration.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to 

state.

WARRANTY

Summary of Contents for 2220273


























Reviews: