Kobelco SK235SR-2 Operation Manual Download

Page: 181 / 308

Maker

Mobil

Brand

MOBIL EAL Envirosyn 46H

４

4.4

USE OF BIO-DEGRADABLE OILS

When using Bio-degradable Oil (BIO OIL), refer to the following information.

Recommended Oil

Precaution for the Use of Oil

When filling the former machine in which mineral oil is charged with BIO oil, try to flush the

machine three times.

The mineral oil will be left in the circuit of the machine without flushing, resulting in the reduction

of effect of biodegradation ability.

When you use BIO OIL, slewing and travel parking brake performance will be reduced because

of lower friction factor of BIO OIL compared to that of mineral oil.

Flushing Procedure

1. Drain mineral oil from the hydraulic tank completely.

2. Drain mineral oil from the cylinder completely.

3. Fill hydraulic oil tank with new BIO oil.

4. After starting engine, move every cylinder 10 strokes respectively.

The abrupt operation may cause burning of seal because of trapped air in the cylinder.

Try to operate first 4 strokes slowly at engine low idling to charge hydraulic oil in the entire cylinder.

5. Idle travel motor right and left for about 3 minutes.

6. Repeat swing operation 10 rotations.

7. Drain BIO oil from hydraulic tank completely.

8. Drain BIO oil from each cylinder completely.

9. Fill hydraulic tank with new BIO oil. Similarly, repeat the procedure 4. to 9. two times.

10. For hydraulic oil in final condition, analyze the hydraulic oil and be sure of amount of remaining

mineral oil.

Bio Oil Change Interval

The BIO oil change interval is 2,000 hours.

For the changing procedure, refer to the section "4.18.A Change Hydraulic Oil".

［

4. MAINTENANCE

］

4-13

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands