Kobelco SK235SR-2 Operation Manual Download

Page: 231 / 308

This will make both high and low pressure

extreme and exert a bad influence on the

pressure switch operation and the air

conditioning system.

-Figure (C) :

Shows that the refrigerant is insufficient.

Have the refrigerant recharged at your

KOBELCO distributor.

４

-Keep the air conditioner ready for use all year round.

Operate the air conditioner at least once every week for several minutes to rotate the compressor

regardless of the season. This will prevent the refrigerant gas from leaking from the compressor

sealing.

-When oil comes out from the pipe joint, contact our dealer/distributor because it is a sign of gas

leaking.

-Follow the following regulations to conserve global environment.

1. Do not release refrigerant which is sealed in this unit in to atmosphere.

2. Extract the sealed refrigerant from unit when disposing this unit.

［

4. MAINTENANCE

］

4-63

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands