Kobelco SK235SR-2 Operation Manual Download

Page: 290 / 308

7.3

OPERATION OF DOZER BLADE

7.3.1

OUTLINE

Blade is attached on lower frame with pin, and is used for backfilling and leveling after digging works

by operating dozer cylinder through the aid of dozer control lever in cab and moving blade up and

down.

7.3.2

DOZER BLADE OPERATION

Read, understand and follow all safety precautions and operation procedures found in this manual

before operating the machine or any attachment.

Start machine and place the safety lock lever in the "UNLOCKED" (down) position.

Move throttle control to the "HI" idle position.

Using boom, arm and bucket controls set the attachment to desired position.

Pull the blade control lever to lift up the blade.

Push the blade control lever forward to lower the blade.

Always place attachments on the ground and lock up the safety lever before leaving the cab.

［

7. OPTIONAL EQUIPMENT

］

7-20

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands