Kobelco SK235SR-2 Operation Manual Download

Page: 84 / 308

ITEM

DEFAULT

Engine Oil

500 Hr

Fuel Filter

500 Hr

Hydraulic Filter

1,000 Hr

Hydraulic Oil

5,000 Hr

Remaining time display to the engine oil change

This display shows the remaining time to the

coming engine oil change.

Remaining time display to the coming fuel filter

replacement This display shows the remaining

time to the coming engine fuel filter

replacement.

Remaining time display to the coming hydraulic

oil filter replacement

This display shows the remaining time to the

coming hydraulic oil filter replacement.

Remaining time display to the coming hydraulic

oil change

This display shows the remaining time to the

coming hydraulic oil change.

C.3 DISPLAY FOR MAINTENANCE

This screen displays the remaining time to the end of recommended replacement interval specified for

filter/oil. After reaching to the end of replacement interval, check and serve them following to section

"Maintenance".

The recommended replacement interval is the accumulated time which is counted by controller when

the engine is running.

This menu is available for confirmation of the following items.

The maintenance screen changes each time the screen change switch is pressed.

Replacement Interval

-The display automatically changes to the main screen, if switch is not operated for 30 seconds.

-For the setting procedure of maintenance time to be performed to the coming oil change in each

type and filter replacement, see "2.3.1.C.4

SET PROCEDURE OF MAINTENANCE SCHEDULE".

［

2. MACHINE FAMILIARIZATION

］

2-22

Summary of Contents for SK235SR-2



























































































































































































































































































Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands

Kobelco SK235SR-2, Operation Manual

Search results

Summary of Contents for SK235SR-2

Reviews:

Related manuals for SK235SR-2

Brands by name

Popular brands