AUTOMATIC FEEDER
SHREDDING USING THE AUTOMATIC FEED SYSTEM Fig.5,
Fig.6 , Fig.7
All cross cut and High Security models can be equipped on
request with a dedicated patented Automatic Feeder which
accepts approximately up to 170 sheets A4 70 gr.
To operate the Automatic Feeder the sheets of paper must be
inserted into the feeder (12) and pushed all the way down as
shown in Fig.5.
Start the shredding by touching the FORWARD button (7) when
the led (15) flashes.
The machine will stop automatically after the last sheet has been
shredded.
The Automatic Feeder is equipped with a special Anti-Jamming
System.
In case the following is inserted into the Feeder (12):
- Folder or crumpled paper
- Multiple stapled sheets
- Sheets with clips
- Glossy paper or Paper heavier than 80 gr sqm
- A higher number of sheets than the allowed number of
150/170 sheets
The Anti Jamming System will stop the operation of the feeder.
To continue shredding, remove the material from the feeder and
make sure that the quality of paper re-inserted into the feeder
can be accepted by the system.
ATTENTION: The operator should consider as a guideline to
evaluate the quality of paper to be shredded that the Automatic
Feeder is based on a similar technology of the drawers installed
in office copy machines.
PAPER JAMS
Should the shredder jam, do the following:
- Unplug the machine from the mains.
- Open the cover with the key (only for high security
“HS”
models).
- Remove the top cover (23) of the automatic feeder by pressing
the buttons on the sides as indicated in figure 6 and pull
upwards.
- Remove the two knobs (13) as indicated in fig. 7 and remove
the metal plate (14)
- Remove the jammed paper.A manual rotation of the rubber
rollers helps in clearing the jam.
Once the blades are free of the paper jam replace the metal
plate (14) secure it with the two knobs (13), then put back on the
top cover (23).
Now your shredder is ready for operation
LOCKABLE COVER
All KOBRA shredders equipped with an Automatic Feeder can
be supplied with a special Lockable Cover (21) including a High
Security non-duplicable key to protect documents from
unauthorized persons while the Automatic Feeder is processing
the shredding operation.
INSTALLATION;
Position the cover over the holes on the hinges and insert the
rivets which come with the cover as indicated in fig.8.
WARNING: once the cover has been fitted with these special
rivets it can no longer be remove
SHRED GUARD
The shredders in the Kobra 245TS , 260TS, Kobra 270TS and
Kobra 310TS range can also come fitted on request with the
'SHRED GUARD' (METAL DETECTION SYSTEM).
This system is set to detect the presence of metal objects
accidentally inserted into the machine (2) of a size which can
damage the cutting knives and instantly cuts it off before they
reach the cutting blades thus prolonging the life of the cutting
blades.
INSTALLATION Fig.2
The SHRED GUARD requires no special installation since it is
fitted inside the shredder in the factory.
OPERATION
Once the machine has been plugged into the mains power
supply, press the ON/OFF button (O) and the bar (P) lights up
and begins flashing for about 30 seconds in order to give the
METAL DETECTION SYSTEM time to start up.
As soon as the bar (P) goes off, your shredder is ready for use.
When paper is inserted into the throat (2), the bar (P) lights up
and the machine automatically begins shredding.
If by any chance the material inserted into the throat (2) of the
shredder contains metal objects of a size which can damage the
cutting knives, the machine shuts down automatically before
these objects reach the cutting blades. The presence of metal
objects is signalled by the flashing light bar (P).
Press the REVERSE button (11) and the machine goes into
reverse so that the operator can remove the metal objects
present on the sheets of paper.
The machine is now ready for shredding.
WARNING!!! When the machine is first switched on, it takes
about 30 seconds for the SHRED GUARD to start up.
In the meantime, the light bar (P) flashes and no shredding can
be carried out.
11
Вы
всегда
можете
купить
это
оборудование
на
сайте
www.office-world.ru
8 800 775-37-18
