2
20
Trouble Shooting Guide
If the unit continues to be fault after the following adjustments please consult
your dealer.
When the picture is not displayed on the monitor
- Please check if the AC-DC power unit is plugged into the AC power outlet
firmly
- Please check if there are any misconnection’s in the cabling.
- Please check if the IRIS mode select switch is set to the correct position i.e. to
the DC mode for the DC driven auto iris lens or VI mode for the Video driven
auto iris lens.
When the picture is blurred
- Please check if the lens is contaminated. Please clean the lens surface
(on both sides) gently with a soft cloth or tissue.
- Please check if the lens is focused properly.
- When you use a manual iris lens, the iris select switch should be
positioned to the ES mode.
- Please check if the monitor is set to brightly. Adjust the brightness or
contrast level on the monitor correctly.
When the color displayed on the monitor is not correct(for Color)
- Please check if the White Balance switch is set to WBM position.
White balance is controlled automatically under the WBA mode for most
situations. When the camera is used under special lighting conditions,
please refer to page 7 in this manual.
- Please check if the monitor’s color adjustment is set correctly.
When the picture is too dark
- Please check if the monitor’s contrast is set too dark.
- Please check if the Gamma select switch is set to 1.0 on the 6
th
pin of the
DIP switch. If it is please move it to the 0.45 position. Gamma 1.0 position
is recommended for use with a LCD monitor.
- Please check if the camera is positioned toward a door or window.
Please set BLC ON is these conditions.
1
19
Specification (B/W)
MODEL
KCB-34(12)
KCB-34(24)
KCB-34(230)
KCB-340(12)
KCB-340(24)
KCB-340(230)
DC12V
DC12V-AC24V ( 4V) Dual AC230V( 30V)
DC12V
DC12V-AC24V ( 4V) Dual AC230V( 30V)
90
mA
90
mA
30
mA
90
mA
100
mA
32
mA
Video Iris/ESC/DC Iris
C-Mount (17.5mm Frange back) ~ CS-Mount (12.5mm Frange back) & Fine focus 1.0mm
240
ON/OFF
0.45/1.0
ON/OFF
STD/MAX
BNC
Red LED
Screw Joint
YES
4Way Slide
4Pin Jack
VI ES DC
DC Level
220
0.45/1.0
ON/OFF
STD/MAX
BNC
Red LED
Screw Joint
4Way Slide
4Pin Jack
VI ES DC
DC Level
220
0.45/1.0
ON/OFF
STD/MAX
BNC
Red LED
Screw Joint
4Way Slide
4Pin Jack
VI ES DC
DC Level
420
0.45/1.0
ON/OFF
STD/MAX
BNC
Red LED
230V AC VDE Code
4Way Slide
4Pin Jack
VI ES DC
DC Level
240
ON/OFF
0.45/1.0
ON/OFF
STD/MAX
BNC
Red LED
Screw Joint
YES
4Way Slide
4Pin Jack
VI ES DC
DC Level
420
0.45/1.0
ON/OFF
STD/MAX
BNC
Red LED
230V AC VDE Code
4Way Slide
4Pin Jack
VI ES DC
DC Level
1/3" Interline CCD, SONY Option : EX-View HAD CCD Version
EIA:512(H)X492(V) CCIR:500(H)X582(V) EIA:768(H)X494(V) CCIR:752(H)X582(V)
420 TV Lines
600 TV Lines
Internal
Internal/Line Lock
Internal
Internal
Internal/Line Lock
Internal
EIA 525 Lines CCIR 625 Lines 2:1 Interlaced
1.0Vp-p Composite. 75 Ohms
More then 50 dB (AGC Off)
STD : 0.05 Lux at F1.4 Option : 0.01 at F1.4 (EX-View HAD CCD version)
ON/OFF by Dip Switch
EIA : 1/60~1/100,000 sec CCIR : 1/50~1/100,000 sec
Standard
0.45 Switchable
1.0 by Dip Switch
Standard : 4dB~32dB Auto Maximum by Dip switch
0.005%
80,000 hours
14° F~122° F ( -10° C~ + 50° C )
Within 90% RH
50(W) x 50(V) x 100(L)
Image sensor
Effective Pixels
H.Resolution
Synchronizing system
Scanning system
Video output
S/N ratio
Min. Illumination
BLC
Shutter Speed
Gamma correction
Gain Control
Smear Effect
MTBF
Power source
Operating current
Lens
Iris Control
Operating Temperature
Humidity
Measurement(mm)
Weight(Approx.g)
Line Lock
Gamma
BLC
AGC
Video Out
Power Indicator
Power Input terminal
Phase V.R
Dip S/W
Auto Iris jack
Iris Mode Slide S/W
DC Iris Adjust volume
Dip S/W
Control
Rear
Pannel
Side
Pannel
