English
4
General safety information
Funai reserves the right to change products at any time without being
obliged to adjust earlier supplies accordingly.
The material in this Extended User Guide is believed adequate for the
intended use of the system. If the product or its individual modules or
procedures are used for purposes other than those specified herein,
confirmation of their validity and suitability must be obtained. Funai
warrants that the material itself does not infringe any United States
patents. No further warranty is expressed or implied.
Funai cannot be held responsible neither for any errors in the content
of this document nor for any problems as a result of the content in this
document. Errors reported to Funai will be adapted and published on the
Funai support website as soon as possible.
•
Warranty
• Do not attempt to take the device apart. There is danger of an
electrical shock. No components are user serviceable. Opening the
device voids the warranty. Do not disassemble or remove covers to
the inside of the device. Repairs may only be done by an authorized
service center. Failure to do so shall void any warranty, stated or
implied.
• Any operation expressly prohibited in this Extended User Guide,
any adjustments or assembly procedures not recommended or
authorized in this Extended User Guide shall void the warranty.
• Do not make any changes or settings that are not described in this
Extended User Guide. Physical injury or damage to the device or loss
of data can result from improper handling. Take note of all warning
and safety notes indicated.
• Do not remove the product label located on the bottom side from
your device; this would void the warranty.
•
Setting up the device
Please read the following instructions when you set up the device.
• Select a stable location.
Select a level, stable place with adequate space for air circulation.
Make sure to allow extra space to open covers and trays.
The setup area should be well-ventilated and away from direct
sunlight or sources of heat, cold, and humidity. Do not set the device
near the edge of your desk or table.
• Place the device on a flat and stable surface.
• The device should be placed securely. If the device should fall, it can
be damaged or can cause injury to people, especially small children.
If the device is dropped it should be inspected by an authorized
service center.
• Position all cables in such a way that no one will stumble on them,
thus avoiding possible injuries to persons or damage to the device
itself.
• Protect the device against direct sunlight, heat, large temperature
fluctuations and moisture. Do not place the device in the vicinity of
heaters or air conditioners. Observe the information on temperature
and humidity in the technical data.
• The device must have sufficient ventilation and may not be covered.
Do not put your device in closed cabinets or boxes. Do not place the
device on soft surfaces such as tablecloths or carpets and do not
cover the ventilation slits. Otherwise the device could overheat or
degrade.
• The area in which you operate the device must be adequately
ventilated, especially if the device is used frequently. Set up your
device in such a way that the Heat or A/C vent's air flow must be
directed away from the work station.
• Never use a gas duster on this device. This gas trapped inside of this
device may cause ignition and explosion.
• In the event that the device becomes too hot, or if you see smoke
coming from the device, you must immediately disconnect the AC
plug from the AC outlet. Have your device examined by trained
professionals at an authorized service center. To prevent the spread
of fire, open flames should be kept away from the device.
• Do not allow liquids to enter into the device. Disconnect the device
from the AC plug if liquids or foreign objects have entered the
device and have your device examined by trained professionals at
an authorized service center.
• Do not allow children to handle the device without supervision. The
packing materials should be kept out of the hands of children.
• Do not press forcefully on the scanner lid when you scan thicker
documents or three-dimensional items, this could damage the
scanner lid and/or the scanner glass.
• Make sure to place the device on a desk or table with adequate
strength. Do not shake the device as this may cause printing failure
or trouble. Do not place the device in a location or environment of
high temperature or high humidity.
•
Power supply
• Check whether the voltage rating of your device (indicated on the
product label located on the bottom side) is adequate for the power
source available at the setup location.
• Do not plug in the device in moist rooms. Never touch the AC power
cord or the AC plug connection with wet hands.
• Set up your device so that the AC plug is easily accessible. In an
emergency, disconnect your device from the power supply by
pulling the AC plug.
• Never touch the AC power cord if the insulation is damaged. Turn
Off the circuit breaker for that AC outlet.
• Damaged wire could cause fire or electrical shock. Keep the AC
power cord straight without being twisted, bent or scraped.
Please contact an authorized service center.
• Before cleaning the surface of your device, disconnect it from the
power supply by pulling the AC plug. Use a soft, lint-free cloth.
Never use liquid, gaseous or easily flammable cleansers (sprays,
abrasives, polishes, or alcohol). Do not allow any moisture to reach
the interior of the device.
• In rare cases, the saved settings can be partly or completely reset
to factory defaults when the AC plug is disconnected or in the event
of a power outage. Do not disconnect the AC plug right after a print
job or after entering settings.
• Press (Power) to turn the device On or Off (Standby).
To completely turn Off the device, you must disconnect the AC plug.
Disconnect the AC plug to shut the device Off when trouble is found
or not in use. The AC plug shall remain readily available.
CAUTION
C
• Turn the device Off (Standby) using
(Power) button
located on the Control panel of the device before you
disconnect the AC plug from the AC outlet to turn the Unit
completely Off.
Continued on next page.
