31
Item
Question
Response
Fan type
Blow type
Filter
Air gun type
What material is the cleaning brush made of?
How long should the filter maintenance period be?
When the power switch is left ON, can ON/OFF control be
performed on the
+
24V side?
Is there a problem with leaving the power supply
continually ON?
Can the DTRY-ELB nozzle be used with the DTRY-ELL?
What is the nozzle made of?
In what sort of situations can abnormalities occur?
DTRY-ELL01 does not have a ground terminal. Is a
ground not needed?
What is the minimum bending radius for each tube?
Will bending the tube have an effect on static charge
removal performance?
Is a set screw for the mounting bracket DTRY-ELQ02
provided? Also, what are the hexagon socket head screws
and set screw made of?
Can the bender nozzle be chopped short and still function
properly?
Can the tube holder DTRY-NZR31 be used with all tubes,
including Teflon, silicone, and urethane?
What is the tube holder made of?
Can we manufacture and use our own nozzle?
Can the Mini Line Filter DTRY-LF080 be connected to the
ionizer body? (Same for blow type)
How long should the period be for replacing the Mini Line
Filter?
Is a power cable provided?
Isn’t a ground needed?
Can the discharging needle be replaced?
Nylon.
If dust appears to be clogging the filter, it is time to replace
it.
It can. Always perform this control on the
+
24V side.
There will be cases where ON/OFF control cannot be
performed on the 0V side.
Do not use the equipment in this way, since plasma
concentrations caused by discharges can build up around
the discharging needle, increasing the risk of ozone
degradation and equipment corrosion.
The DTRY-ELL nozzle uses a different thread size than the
DTRY-ELB nozzle for connecting to the main body. Please
purchase the nozzle specially made for each model.
The connection part (cone-shaped part) to the ionizer
main body is made of aluminum alloy, while the tips are
made of stainless steel.
Abnormalities can occur in such cases as when the cap is
loose, when the nozzle comes into contact with a ground,
or when the discharging needle is exceptionally dirty.
When abnormal output is detected, a red lamp lights up.
Since the mounting holes on the side of the main body
(the rear side) share ground ter minals, the unit is
grounded when brackets are installed on a ground body. If
installed on an insulator, however, be sure to provide a
separate ground.
Conductive urethane tube: R15 mm [0.59 in.]; Teflon tube:
R50 mm [1.97 in.]; silicone tube: R10 mm [0.39 in.]; and
bender nozzle: R40 mm [1.57 in.].
It has virtually no effect. However, it is conceivable that
bending it at minimum bending radius at several places
could affect performance.
A set screw is provided with the product. Both items are
made of stainless steel.
No, it would become unusable.
Since the DTRY-NZR31 is compatible with tubes of outer
diameter
φ
6 [0.236 in.], it is specially made for the
urethane tube (DTRY-ADN-U). If using this holder to
secure other tubes in place, secure in an insulator.
The holder portion is made of POM, and the screws are
made of stainless steel. Ever ything else is made of
aluminum alloy.
Always use Koganei nozzles. For nozzles with special
shapes, consult with Koganei.
The blow type tube diameter is for Rc1/8, while the LF080
is for R1/4. The LF080 cannot be directly connected
together.
It is impossible to tell from outward appearance. While
replacement should be performed when the flow rate
declines, Koganei recommends replacement at around
once per year.
No cable is provided. Moreover, for power, 24VDC (750
mA or more) should be provided by the customer. For the
air gun type, the DTRY-ELC04-140W special AC adaptor is
available.
The structure does not require a ground.
The customer cannot perform this replacement. Consult
with Koganei.