Kohler GM89754-KP1 Installation Instructions Manual Download

Page: 8 / 16

TT-1605 5/16

GM89754-A

1. Brackets (GM86091 qty. 3), bolts (X-6224-20 qty. 6), and nuts

(X-6210-7 qty. 6)

2. Brackets (GM86091 qty. 2), bolts (X-6224-20 qty. 4), and nuts

(X-6210-7 qty. 4)

3. Brackets (GM86091 qty. 2), bolts (X-6224-20 qty. 8), and nuts

(X-6210-7 qty. 8)

4. Bracket (GM86091), bolts (X-6224-20 qty. 4), and nuts

(X-6210-7 qty. 4)

5. Brackets (GM86091 qty. 2), bolts (X-6224-20 qty. 6), and nuts

(X-6210-7 qty. 6)

6. Wing nuts (X-276-9 qty. 3) installed when installing engine

roof.

7. Wing nuts (X-276-9 qty. 2) installed when installing alternator

roof.

8. Wing nuts (X-276-9 qty. 2) installed when installing controller

panel.

9. Wing nuts (X-276-9 qty. 2) installed when installing exhaust

panel.

10. Foam (GM87549 or GM88912). Insert foam into all rails. Cut

to fit.

11. Corner foam (GM87547 or GM88910 qty. 12). Install three

per corner.

Figure 13

Bracket Location/Installation

Summary of Contents for GM89754-KP1

















Search results

Summary of Contents for GM89754-KP1

Reviews:

Related manuals for GM89754-KP1

Brands by name

Popular brands

Kohler GM89754-KP1, Installation Instructions Manual

Search results

Summary of Contents for GM89754-KP1

Reviews:

Related manuals for GM89754-KP1

Brands by name

Popular brands