background image

BEFORE YOU BEGIN

BEFORE YOU BEGIN

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.

Do not lift

the whirlpool by the piping or pump, or use the
piping or pump for structural support of the
whirlpool.

All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-

CAUTION: Risk of product damage.

please leave these

instructions for the consumer.

·

·

We recommend this whirlpool for corner, drop-in, or
flush installations. An undermount kit is also
available.
Inspect the whirlpool for damage before you begin
installation.
You must install this whirlpool to an adequately
supported, level subfloor.
Confirm adequate support for a rim-mounted faucet,
if used; large faucets that may be inadvertently used
as a means of support are not appropriate or safe
for this installation.
Consult local and national codes.
Kohler Co. reserves the right to make revisions in
the design of products without notice, as specified in
the Price Book.

1036303-T01-A

INSTALLATION INSTRUCTIONS

WHIRLPOOL

K-1111-VLN

1

ã

, 2011

Copyright Kohler China Ltd., 2011

C

1141609-T01-A

Summary of Contents for K-1111-VLN-0




















Reviews: