Care and Cleaning
SYMPTOMS
PROBABLE CAUSES
RECORRECTIVE ACTION
1. Dual System bath
does not start.
A. Controller is not power on.
A. Set/reset ELCB breaker; check wiring.
B. User keypad cable loose or damaged.
B. Check wire connections. If necessary,
replace user keypad.
C. User keypad does not work.
C. Replace user key pad.
D. Pump does not work.
D. Replace pump.
2. Pump stops
automatically
within 30 minutes.
A. ELCB trips.
A. Correct ELCB trips.
3. Pump does not
stop automatically
after 30 minutes.
A. Controller trips.
A. Replace controller.
4. Pump does not
stop when pump
on/off button on
user keypad is
pressed.
A. User keypad cable loose or damaged.
A. Check wire connections. If necessary,
replace user keypad.
B. User keypad does not work.
B. Replace user keypad.
5. Pump operates
but cannot adjust
massage strength.
A. User keypad cable loose or damaged.
A. Check wire connections. If necessary,
replace user keypad.
B. User keypad does not work.
B. Replace user keypad.
C. Controller does not work.
C. Replace the controller.
D. Electronic adjustment valve does not work.
D. Replace electronic adjustment valve.
6. Pipe cleaning
does not work.
A. User keypad cable loose or damaged.
A. Check wire connections. If necessary,
replace user keypad.
B. User keypad does not work.
B. Replace user keypad.
C. Pump does not work.
C. Replace pump.
D. Controller does not work.
D. Replace the controller.
Troubleshooting
Cleaning Your Acrylic Bath
□
Use a mild detergent such as liquid dishwashing soap and warm water for cleaning. Do not use abrasive
cleaners that may scratch or dull the surface.
□
Carefully read the cleaner product label to ensure the cleaner is safe for use on the material.
□
Always test your cleaning solution on an inconspicuous area before applying to the entire surface.
□
Do not allow cleaners to sit or soak on the surface.
□
Wipe surfaces clean and rinse completely with water immediately after cleaner application. Rinse and dry
any overspray that lands on nearby surfaces.
□
Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring pad to
clean surfaces.
NOTE :
To restore dull or scratched units : Apply white automotive polishing compound with a clean rag. Rub scratches
and dull areas vigorously. Wipe off residue. Follow with a coat of white automotive paste wax. Do not wax areas
where you walk or stand.
Cleaning Your User Keypad
Use a soft cloth to wipe the keypad and remote control after each use. If the surface becomes dirty, use a non-abrasive
soap and warm water to clean.
Kohler Co.
11 1241693-X2-B
Summary of Contents for K-97260X
