background image

-6-

Bath:

Pillow:

Faucet:

Your new vinyl pillow can be routinely cleaned

with mild soap and water. Remove stubborn stains with
cleaning products recommended for vinyl.

Periodically use a vinyl treatment product to

rejuvenate the appearance of the vinyl skin.

All Finishes: Clean the finish with a mild soap

and warm water. Wipe entire surface completely dry
with a clean soft cloth. Many cleaners may contain
chemicals, such as ammonia or chlorine, which could
adversely affect the finish and are not recommended
for cleaning.

Do not use abrasive cleaners or solvents on Kohler
faucets and fittings.

CARE AND CLEANING OF YOUR PILLOW

CLEAN-UP AFTER INSTALLATION

When cleaning up after installation, do not use abrasive
cleansers as they may scratch and dull the surface.
Use warm water and liquid, non-abrasive detergent to
clean the surface.

Stubborn stains, paint, or tar can be removed with
mineral spirits. Do not use cleaners containing solvent.
Plaster can be removed by scraping with wood edge.
Do not use metal scrapers, wire brushes, or other metal
tools. One of the powder type detergents may be used
on a damp cloth to provide mild abrasive action to the
residual plaster.

DIRLLING AND CUTTING ACRYLIC

DRILLING:

NOTE:
CUTTING:

Small holes can be drilled with a twist drill,

but the cutting edge MUST be backed off with an oil
stone (the sharp edge dulled). Large holes must be
drilled with a hole saw. Maximum drill size-12mm. Drill
speeds-6mm x 1800 RPM-12 mm x 900 RPM.

Always drill from acrylic surface.

If for any reason the acrylic requires cutting,

use a fine tooth hacksaw and proceed with caution.
Edges can be smoothed with a second-cut file and
medium-fine sandpaper. If the surface of the acrylic
should happen to be damaged, it can be restored by
polishing with an abrasive cleaner . Deep scratches
can be removed by rubbing with 600 grade wet & dry
sandpaper then polishing.

12mm

6mmx

/

12mmx900

600

1800

/

Both handles open with turning counter-clockwise and
close with turning clockwise. Turn on the faucet, water
flows from the bath spout. Pull diverter, water flows
form the handspray. When turn off the faucet, the
diverter returns to the bath postion.

OWNER ' INSTRUCTIONS: FAUCET SECTION

1206725-T01-A

Summary of Contents for K-99023T








Reviews: