Komatsu A31001 Operation & Maintenance Manual Download | Manualshive

Page: 164 / 376

background image

1.

Highlight the layer to be deleted, and tap “Delete” button.
The screen changes to “MessageBox” screen.

2.

To delete all Points and Linework(s) saved in the layer, tap
ENTER button.
All Points and Linework(s) saved in the layer are deleted.

3.

Tap RETURN button to return the screen to the previous
screen.

IMPORT 3D POINTS FILE AND 3D LINEWORK FILE

The point and line work can be imported.
Highlight the layer to be saved, and tap the “Import” button.
The screen changes to “Import Project Data” screen.
Files which can be imported are the two types of point and line
work.

CONTROL BOX

SETTING

7-48

«
...
162
163
164
165
166
...
»

Summary of Contents for A31001

























































































































































































































































































































































































Reviews:

No comments

Related manuals for A31001

Brand: CRAWLER Pages: 22

Brand: Kubota Pages: 112

Brand: New Holland Pages: 31

Brand: JackRabbit Pages: 22

Brand: jcb Pages: 18

Brand: Hitachi Pages: 278

Brand: WCM Pages: 69

Brand: jcb Pages: 24

Brand: Hyundai Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands