Komatsu A31001 Operation & Maintenance Manual Download | Manualshive

Page: 360 / 376

background image

4.

The screen for inputting the name of “Layer” to be saved
and “Point description” (bucket edge position data) is dis-
played.
The name of set Layer and Point description (bucket edge
position data) are displayed if they have been already set.

CREATE NEW LAYER TO RECORD DATA

Select the “<new layer>” on the layer column, and input a
name.
If the layer for saving data is in a list, select the layer.

METHOD FOR INPUTTING NEW POSITION DETAILS NAME

1.

Select the “<new description>” in “Point description” col-
umn, and input any name.
If the name of the point is in a list, select that “Point” name.

USE OF TOPO SURVEY

EXECUTIONS

8-50

«
...
358
359
360
361
362
...
»

Summary of Contents for A31001

























































































































































































































































































































































































Reviews:

No comments

Related manuals for A31001

Brand: Equipter Pages: 16

Brand: Case Pages: 21

Brand: Takeuchi Pages: 18

Brand: Skandia Elevator Pages: 24

Brand: Hitachi Pages: 16

Brand: Worldwide Construction And Forestry Division Pages: 288

Brand: Terex Pages: 100

Brand: NPK Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands