Contours color - Set............................................ 7-104
Control box............................................................3-20
CONTROL BOX......................................................7-3
Control box - Adjust position................................. 3-46
Control box - Check looseness of bolts................ 8-30
Control box - Check screen display...................... 8-32
Control box - Install............................................... 3-38
Control box - Phenomena and actions..................3-74
Control box - Precautions....................................... 2-8
Control box - Remove........................................... 3-36
Control box - Remove, install, adjust position.......3-36
Control box - Shut down....................................... 3-52
Control box - Start.................................................3-50
Control box screen display....................................8-56
Control levers and pedals..................................... 3-18
Control pattern change-over valve - Change control
patterns............................................................6-2
Control patterns other than standard control method...
.........................................................................6-3
Control Point File - Copy from USB flash drive.....7-18
Control point files - Import from Project File..........7-18
Control point setting contents............................... 7-14
Control Point settings............................................7-13
Control Points - Delete..........................................7-16
Control Surface offset - Adjust................................ 8-9
Conventional bucket file - Select.........................7-153
Coordinates - Set................................................ 7-118
Create new Project File...........................................7-6
Cross hair display - Set for steering......................7-65
Cross section color - Set.......................................7-98
Cross section color - Set display.........................7-105
Cross section filling color - Set display............... 7-106
Crown road surface...............................................7-36
Crown Road Surface - Create...............................7-37
Crown road surface setting contents.................... 7-37
Cup holder............................................................ 3-33
Current Abnormality display switch....................... 3-11
Cut Fill display color - Set..................................... 7-67
Cut fill settings.............................................. 7-52,7-67
Cylinder function state caution lamp..................... 3-14
Cylinder stroke sensor case bolt - Check / Clean... 4-3
D
Daily calibration.....................................................8-30
Data - Output...................................................... 7-125
Design data settings............................................. 7-92
Direction of travel - Set......................................... 7-87
Display - Set by Point Options tab........................ 7-99
Display bucket edge coordinates..................8-26,8-44
Display bucket edge position................................ 8-26
Display bucket edge position alignment station.... 8-27
Display distance between bucket edge and the de-
sign surface................................................... 8-27
Display distance between center line and bucket
edge position................................................. 8-27
Display of travel mode...........................................8-11
Display options......................................................7-70
Display Options - Display contours, set interval of
contours....................................................... 7-103
Display Options contents...................................... 7-71
Distance - Set......................................................7-116
E
Elevations - Offset lower...........................7-136,7-138
Enable/Disable setting - Change........................ 7-143
Engine - Start........................................................ 3-47
Engine - Stop........................................................ 3-54
Error by failure in electrical component.................3-74
Every 500 hours maintenance................................ 4-3
Existing Point - Delete...........................................7-26
Existing Point - Edit...............................................7-25
Explanation of components.....................................3-6
Explanation of machine monitor equipment............3-6
F
Facing Angle Compass (green) - Set range......... 7-66
Fine Digging mode................................................8-19
Fine digging mode screen - Set............................ 8-19
Fine Digging mode settings.................................. 7-58
Fixed Degrees of Direction of travel - Set............. 7-88
Flat plane surface................................................. 7-29
Focus Point - Set.......................................... 7-83,7-86
Foreword.................................................................1-1
Fuse...................................................................... 3-33
G
General view........................................................... 3-2
Geoid File - Copy.................................................. 7-21
Geoid File - Copy to USB flash drive.................... 7-23
GNSS antenna - Install ........................................ 3-61
GNSS antenna - Remove..................................... 3-60
GNSS antenna - Remove / Install.........................3-60
GNSS antenna and antenna for network modem - In-
stall................................................................ 3-68
GNSS antenna and antenna for network modem -
Remove......................................................... 3-64
GNSS antenna and antenna for network modem -
Remove / Install............................................. 3-64
GNSS antenna and cable - Check........................8-30
GNSS communication - Check status...................8-43
GNSS fluctuation reduction filter - Set................ 7-194
GNSS Radio - Configure.....................................7-148
GNSS radio device - Check.................................. 8-30
GNSS radio device - Configure...........................7-146
GPS receiver not connected! - Action for the mes-
sage............................................................... 3-75
Grade Indicator - Invert color................................ 7-59
Grade Indicator - Set range.................................. 7-60
Grade Indicator (green) - Set width.......................7-60
Grade Indicator settings........................................7-58
Grade transitions - Set display............................7-107
Grades - Set........................................................7-117
Guidance setting - Contents................................. 7-54
INDEX
9-2
Summary of Contents for A31001
