Komatsu A31001 Operation & Maintenance Manual Download

Page: 51 / 376

CUP HOLDER

The cup holder is located on the left side of the operator's seat.

POWER SUPPLY OUTLET
24V power supply

NOTICE
Do not use this as a power supply for 12 V equipment.
This will cause a failure of the equipment.

When cigarette lighter is removed, the lighter socket can be
used as a power source.
The capacity of the cigarette lighter is 85 W (24 V x 3.5 A).

REMARK

Use 24 V power source while engine is running.

12V power supply

Capacity of this power supply is 144 W (12 V x 12 A).

• When it is used at one place: 144 W (12 V x 12 A)
• When it is used at 2 places: 144 W in total

REMARK

Use this power source while engine is running.

FUSE

NOTICE
Turn the starting switch to OFF position, then turn the battery disconnect switch to OFF position always
before replacing the fuse.

• The fuse holder for the fuse 1 (A) is installed at the rear of

the operator's seat. The fuse holder for the fuse 2 (B) is in-
stalled at the rear left of the operator's seat.

• The fuses protect the electrical component and wiring from

burning out.

• If the fuse is corroded, or loose in the fuse holder, or looks

white powdery, replace it.

• Replace the fuse with the one of the same capacity.

OPERATION

EXPLANATION OF COMPONENTS

3-33

Summary of Contents for A31001

























































































































































































































































































































































































Search results

Summary of Contents for A31001

Reviews:

Related manuals for A31001

Brands by name

Popular brands

Komatsu A31001, Operation & Maintenance Manual

Search results

Summary of Contents for A31001

Reviews:

Related manuals for A31001

Brands by name

Popular brands