background image

INSTRUMENTS AND CONTROLS

103

3.2.5 COVERSWITH LOCK

Use the ignition key to open and close the covers with lock.

For details on the position of the covers with lock, see "3.3.17 
LOCKING THE MACHINE".

Introduce the key completely (6 mm from the point where the key 
narrows), then turn it. If the key is turned when it is inserted only 
partially into the lock, it may break.

OPENING AND CLOSING THE COVERS WITH LOCK

Opening

1 - Insert the key into the lock.
2 - Turn the key counterclockwise and open the cover.

Closing

1 - Close the cover and insert the key into the lock.
2 - Turn the key clockwise and extract it.

CAB DOOR LOCK OPENING AND CLOSING

Opening

1 - Insert the key into the lock.
2 - Turn the key anticlockwise and open the cab door.

Closing

1 - Close the cover and insert the key into the lock.
2 - Turn the key clockwise and extract it.

RYA01680

RKA13360

WEAM012405

Summary of Contents for PC16R-3

































































































































































































































































































Reviews: