Machine model
PC500LC-10R
Engine
SAA6D125E-5
Item
Measurement condition
Unit
Standard value for
new machine
Repair limit
Arm time lag
•
Hydraulic oil temperature: 45 to
55 °C
•
Fuel control dial: MIN (Low idle) po-
sition
•
Working mode: P (Power Mode)
•
Set the arm at the most OUT posi-
tion. Time required from when the
arm stops near the vertical point and
to when starts moving to the arm IN
side again by operating the arm con-
trol lever to the arm IN side
•
Measuring posture: See “Machine
posture and procedure for measur-
ing performance”, “Fig. 13”.
sec
3.0 or less
3.6 or less
Bucket time lag
•
Hydraulic oil temperature: 45 to
55 °C
•
Fuel control dial: MIN (Low idle) po-
sition
•
Working mode: P (Power Mode)
•
Set the bucket at the maximum arm
OUT position. Time required for
bucket to start moving toward buck-
et CURL side again after stopping
once around the vertical position by
operating the bucket control lever to-
ward the bucket CURL side
•
Measuring posture: See “Machine
posture and procedure for measur-
ing performance”, “Fig. 14”.
sec
3.0 or less
5.0 or less
Oil leakage
Machine model
PC500LC-10R
Engine
SAA6D125E-5
Item
Measurement condition
Unit
Standard value for
new machine
Repair limit
Oil leakage from
cylinder
•
Hydraulic oil temperature: 45 to
55 °C
•
Fuel control dial: MAX (High idle)
position
•
Measure the leakage for 1 minute
while relieving the travel motor or
cylinder to be measured
cc/min
4.5
20
Center swivel
joint
10
50
STANDARD VALUE TABLE FOR MACHINE: PC500LC-10R
20 STANDARD VALUE TABLE
20-24
PC500LC-10R
Summary of Contents for PC500LC-10R
