4.
Select “Maintenance Notice Time Setting”. Set the notice
time with the function switches on the “Maintenance Notice
Time Setting” screen.
Default value: Maintenance notice time set on the machine
monitor (Recommended by the manufacturer and not
changeable).
Set value: Maintenance notice time can be arbitrarily set.
Maintenance reminder function works according to this
set time in operator mode (the time can be increased or
decreased in 10-hour unit).
F3: Decreases the value.
F4: Increases the value.
F5: Set value is canceled. The screen returns to “Mainte-
nance Mode Setting” screen.
F6: Enters the set value. The screen returns to the “Main-
tenance Mode Setting” screen.
REMARK
• Press F6 to enter the setting. The screen returns to the
“Maintenance Mode Setting”, and the setting is ena-
bled.
• If the setting item is changed when the maintenance
mode setting is turned “ON” after running the machine
more than an hour from the setup, the change is recog-
nized as a reset operation.
5.
Select one of the maintenance items. When the individual
maintenance item screen is displayed, select “On or Off
Setting”.
F3: Moves the selection downward.
F4: Moves the selection upward.
F5: Selection is canceled. The screen returns to “Mainte-
nance Mode Change” screen.
F6: Enters the selected item. The individual maintenance
item moves to the screen to “ON”, “ON (Breaker Syn-
chronization)”, and “OFF” screen.
REMARK
• The screen shown is “Additional Hydraulic Oil Filter Change Interval” as an example.
• If “ON (Breaker Synchronization)” is selected, “B ON” is shown on “On or Off Setting”.
6.
On the individual maintenance item screen, select either
“ON” or “ON (Breaker Synchronization)” or “OFF” with a
function switch.
“ON”: Enables the function of the individual maintenance
item in “operator mode”.
“ON (Breaker Synchronization)”: Enables the function of
the individual maintenance item in “OPERATOR MODE”.
Maintenance remaining time is reduced at an accelerat-
ed rate according to the breaker use remaining time.
“OFF”: Disables the function of the individual maintenance
item in operator mode.
F3: Moves the selection downward.
F4: Moves the selection upward.
30 TESTING AND ADJUSTING
SET AND OPERATE MACHINE MONITOR
PC500LC-10R
30-141
Summary of Contents for PC500LC-10R
