bizhub C360i/C300i/C250i
3
1
<Consumables>
1.4
Regulation notices
About certified model name
This product is certified by the following model name in U.S.A., Canada,
Mexico, Brazil and Europe:
KONICA MINOLTA branded model C302302 (bizhub C360i, bizhub C300i
and bizhub C250i).
For other countries than the above, this product is certified by the follow-
ing model names:
KONICA MINOLTA branded model bizhub C360i, bizhub C300i and
bizhub C250i.
CE Marking (Declaration of Conformity)
for users of the European Union (EU)
Hereby, Konica Minolta declares that the radio equipment models speci-
fied above are in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the follow-
ing internet address:
"https://www.konicaminolta.eu/en/business-solutions/support/down-
load-center.html".
Choose your product and open the section "Safety Documents".
7
WARNING
-
This device must be used with a shielded interface cable. The use
of non-shielded cables is likely to result in interference with radio
communications and is prohibited under EU directives.
If IC-420 is installed:
This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be re-
quired to take adequate measures.
Maximum radio-frequency power transmitted in the frequency band
(EIRP):
Note: 5 GHz may not be available
This radio equipment is restricted to indoor use only. Outdoor use is pro-
hibited.
This restriction applies to all the countries listed in the table below.
For Brasilia users/ Para usuários de
Brasília
The UK-221 (includes wireless module, model WN4521L) are not provid-
ed for the Brazilian market./ O UK-221 (inclui módulo sem fio, modelo
WN4521L) não é fornecido para o mercado brasileiro.
Using this product in a poorly ventilated room for a
long time or producing a large volume of copies or
prints may cause the odor of exhaust air from the ma-
chine. Ventilate the room well.
The inside of this product has areas subject to high
temperature, which may cause burns.
When checking the inside of the unit for malfunctions
such as a paper misfeed, do not touch the locations
(around the fusing unit, etc.) which are indicated by a
"Caution HOT" caution label. A burn could result.
Unplug the product when you will not use the product
for long periods of time.
When using the machine, do not look at the light of the
lamp for a prolonged time. Eyestrain could result.
Do not use stapled paper, conductive paper (such as
silver paper or carbon paper) or treated heat-sensi-
tive/inkjet paper, otherwise a fire may result.
Do not throw toner or a container that contains toner
(e.g., toner cartridge, developing unit and Waste Toner
Box) into an open flame. The hot toner may scatter and
cause burns or other damage.
Do not leave toner-related parts (e.g., toner cartridge,
developing unit and Waste Toner Box) within easy
reach of children. Licking any of these parts or ingest-
ing toner could damage your health.
Do not store toner-related parts (e.g., toner cartridge,
developing unit and Waste Toner Box) near devices
susceptible to magnetism, such as precision equip-
ment and data storage devices, otherwise they may
malfunction. They could cause these products to mal-
function.
Do not force open the toner-related parts (e.g., toner
cartridge, developing unit and Waste Toner Box). If
toner tumbles from the toner bottle, take utmost care
to avoid inhaling it or even getting skin contact.
If toner lands on your skin or clothing, wash thoroughly
with soap and water.
If you inhale toner, move to a place with fresh air and
gargle with a lot of water repeatedly. Should you get
symptoms such as coughing, seek medical advice.
If you get toner into your eyes, immediately rinse them
with running water for over 15 minutes. Seek medical
advice if irritation persists.
If you swallow toner, rinse out your mouth and drink a
few glasses of water. Seek medical advice if neces-
sary.
Never touch the electrical contacts of the units (e.g.,
toner cartridge and developing unit), as an electrostat-
ic discharge may damage the product.
Before handling, see the user documentation for the
safety information.
<If instructed to replace the fusing unit>
The fusing section is extremely hot. Before replacing
the fusing unit, be sure to open doors and covers of
the machine. Then, leave the machine to stand idle for
a specified period of time and make sure that the fus-
ing section has cooled down to room temperature.
Failure to follow these instructions could result in a
burn.
Module Name, Option
Frequency Band
Radiation. Power
UK-221 includes ap-
proved Wireless
module, MODEL
WN4521L:
2.4 GHz
Max. 20 dBm
5 GHz
Max. 23 dBm
EK-609 includes ap-
proved Wireless mod-
ule, MODEL
MBH7BLZ02:
2.4 GHz
Max. 3 dBm
AT
BE
BG
CH
CY
CZ
DE
DK
EE
EL
ES
FI
FR
HR
HU
IE
IS
IT
LI
LT
LU
LV
MT
NL
NO
PL
PT
RO
SE
SI
SK
TR
UK
