Konica Minolta LU-302 Installation Manual Download | Manualshive

Page: 3 / 11

background image

E-3

(7) Remove the lower right cover from the paper

feed cabinet. (Two screws)

(8) Remove the knockout from the front right cover

using nippers.

(9) Remove the two knockouts from the rear right

cover using nippers.

(10) Remove the two knockouts from the lower right

cover using nippers.

(11) Install the supplied mounting brackets C onto

the two places. (Two supplied screws B each)

(12) Install the supplied mounting bracket B onto the

supplied rail.

«
1
2
3
4
5
...
»

Summary of Contents for LU-302












Reviews:

No comments

Related manuals for LU-302

Brand: GE Pages: 20

Brand: GE Pages: 2

Brand: Gates Pages: 2

AJHVF21G - HD EVF - MULTI-LANG

Brand: Panasonic Pages: 4

Brand: IFM Pages: 43

Green Motion DC 22

Brand: Eaton Pages: 65

Brand: PAJ Pages: 95

Brand: Gamko Pages: 32

Brand: i-onik Pages: 6

HighLine ABF0166

Brand: Mactronic Pages: 2

Brand: EcoFlow Pages: 42

Vision Premier 2393

Brand: Kodak Pages: 6

Brand: MFJ Pages: 60

Ares OPzV Series

Brand: Narada Pages: 26

4gb Compact Flash Ultra II - 4gb Ultra II Compact Flash Memory Card

Brand: SanDisk Pages: 1

ClickShare CSC-1

Brand: Barco Pages: 3

MILSCO KIT# C746700

Brand: K&M Pages: 2

Brand: Car-Interface Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands