A. COMPONENTS
5.1
Align mounting bracket
5.1
vertically
5.2
Mark the drill holes.
5.4
WOODEN BEAM
- Wood screw 4,5 x 35 mm
3.a
drill,
countersink,
blow out,
attach bracket,
screw in wood screws
5.5
PERFORATED BRICKS,
4.5
CONCRETE
- Plastic anchor 6 x 30 mm
3.b
-
with wood screw 4,5 x 35 mm
3.a
drill, countersink, blow out,
set the anchor,
attach bracket, screw in wood
screws
5.3
Pre-drilling
5.3
e.g.: ø 6 mm
5.3
Expansion anchor
5.3
ø 3 mm Wood
5.3
screw
D. DISINFECTANT BOTTLE
C. PREPARING HOLDER
TECHNICAL DATA
Please read these assembly instructions carefully!
DIMENSIONS
- Dimensions: W x D x H: 154 x 155-193 x 90 mm
- Bottle size: width x depth: max. ø/
■
102 mm
- Clamping range: depth 65 - 102 mm
- Drip cup: ø 70 x 47 mm
MATERIAL
- Holder, bracket: Steel
- Drip cup: Polyamide
- Knurled knobs: Polyamide, steel, zinc
- Threads: Steel, brass, zinc
SURFACE 80370-000-55 black
80370-000-76 pure white
powder-coated
WEIGHT 0.52 kg
SAFETY INSTRUCTIONS
The safety of the stand depends on the:
MOUNTING
Ensure that all screw connection are tight.
WALL CONDITION
Only use the product on suitable walls, i.e. mount only on
load-bearing walls. Weak walls are unsuited as well as
wall areas where running wires and pipes are hidden
behind. The screws and dowels
2
supplied are not
convenient for all walls. In case of any doubt consult a
qualified expert.
LOAD
Only for disinfectant bottles with suitable size;
see above TECHNICAL DATA.
SURROUNDINGS
Please avoid respectively prevent negative
external influences (knocks, dragging, vibrations,
wind, humidity etc.)
MAINTENANCE
Regularly clean the base
INSTALLATION INSTRUCTIONS
A. COMPONENTS
1
Bottle holder
2
Drip cup
3
Accessories bag (6-16312-1-00)
3.a
Wood screw 4,5 x 35 mm (2x)
3.b
Anchor (plastic) ø 6 x 30 mm (2x)
4
Accessories bag (6-80370-1-55/76)
4.a
Knurled knob M5 (2x)
4.b
Washer ø 5,3 mm (2x)
4.c
Carriage bolt M5 x 12 mm (2x)
4.d
Holding bracket
4.e
Rubber pads ø 13 mm (4x)
B. WALL MOUNTING
5
see fig.
5.1
-
5.5
C. PREPARING DISINFECTANT HOLDER
6
Open the accessories bag
4
and attach the bracket
4.d
6
to the bottle holder
1
:
6
- Slide the bracket
4.d
from outside over the
6
-
mounting bracket,
6
- insert the carriage bolts
4.c
from the inside,
6
- thrust washers
4.b
over the threads,
6
- screw on knurled knobs
4.a
.
7
Glue the rubber pads (4.e) to the rear side of the base
7
(also recommended for wall mounting).
8
Press the Drip cup
2
from above into the opening.
8
As necessary, it can be removed for cleaning.
D. DISINFECTANT BOTTLE (not included in delivery)
1
9
Place the disinfectant bottle in the bottle holder,
10
clamp the bottle by means of the bracket
4.d
,
11
tighten both knurled knobs
4.a
.
INFORMATION
NOTE: The holder for disinfectant is not a
NOTE:
medically certified product.
- Negative effects of the disinfectant on the products
-
(surfaces, material) are not known to us.
- Nevertheless, we recommend to always remove possible
-
residues of the disinfectant in order to avoid possible
-
damage and to enjoy the product as long as possible.
- For cleaning purposes use a slightly damp cloth and
-
a non-abrasive cleaning agent.
Disinfectant is not included in the scope of delivery.
80370 Holder for disinfectant
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
80370-000-55/76 Rev.3a 03-79-922-00 6/20
B. WALL MOUNTING
MOUNTEXAMPLES
PREPARING
