background image

Product Description

2

AM4301 User's Guide

1.3

Board Specifications

* Designed to meet or exceed

Features

Description

Compliancy

AMC.0  R2.0

AMC.1  R1.0

OS Compatibility

RedHat Linux Enterprise 4

IPMI Features

Management Controller compliant to PICMG 3.0, AMC.0 R1.0 and IPMI v1.5 rev 1.1. 

Management Controller is run time field reprogrammable without payload impact. 

Robust fail safe reprogramming implementation (which includes two firmware 

images) that could perform automatic or manual rollback if a problem occurs during 

critical reprogramming phase. 

Remote upgrade capability from all IPMI interfaces (via IPMB). 

Management Controller self test which can detect failure under its code integrity and 

trig an automatic rollback. 

Supervisory

Hardware system monitor through IPMI (voltages, currents, temperature),  

temperature monitor / alarm; board temperature sensor, power failure.

Mechanical

181.5 x 75 x 18.96 mm, Single-width mid-size

181.5 x 75 x 30.16 mm, Single-width Full-height

Power Requirements

Management power is less than 150mA peak at 3.3V

Payload power is 15W

Environmental 

Temperature*

Operating: 0-55°C/32-131°F

Storage and Transit: -40 to +70°C/-40 to 158°F

Environmental 

Humidity*

Operating: 15% to 90% @55°C/131°F non-condensing 

Storage and Transit: 5% to 95% @ 40°C/104°F  non-condensing

Environmental Altitude*

Operating: 4,000 m / 13,123 ft

Storage and Transit: 15,000 m / 49,212 ft

Environmental Shock*

Operating: 30G, half-sine 11ms, each axis 

Storage and Transit: Bellcore GR-63-CORE Section 4.3

Environmental 

Vibration*

Operating: 1.0G, 5-500Hz each axis 

Storage and Transit: 2.0G, 5-50Hz;  3.0G, 50-500Hz each axis

Reliability

MTBF: > 566 000 hours @ 40 C / 104 F (Telcordia SR-332, Issue 1)

Safety / EMC

Meet or exceed:

Safety: UL 60950-1 1st Ed.; CSA C22.2 No 60950-1-03; EN 60950-1:2001; IEC60950-1

EMI/EMC: FCC 47 CFR Part 15, Class B; CE Mark to EN55022/EN55024

Warranty

Two years limited warranty

Summary of Contents for AM4301
































Reviews: