Using Effects
70
10.Access the P8: IFX– IFX page, and edit the
parameters of the insert effect you selected.
Press the IFX 1–5 tabs and edit the parameters.
Effect 1 On/Off:
Turns the insert effect on/off. This is
linked with the on/off setting in the Insert FX Setup
page.
P (Effect Preset):
Selects an effect preset. The M50’s
internal memory contains “effect presets” which are
parameter settings for each effect from 001: Stereo
Compressor through 170: Early Reflections.
Effect parameters you edit are saved as part of each
program, but effect presets allow you to save and recall
your favorite parameter settings for each effect. If
you’ve come up with an effect setting you like, use the
menu command Write FX Preset to save it as a preset
so that you can easily recall it in a different program or
mode.
Double-size effects
Double-size effects (154: St.Mltband Limiter – 170:
Early Reflections) use twice as much space as other
effects.
You can use double-size effects for insert effects IFX1–
IFX4 and master effect MFX1. However, because it
takes up two units of effects power, the next-numbered
effect will be unavailable. For example, if you’ve
selected a double-size effect for IFX1, you won’t be able
to use IFX2. If you’ve selected a double-size effect for
MFX1, you won’t be able to use MFX2.
An example of when a double-size effect is selected for IFX1
and IFX4
Master effects
11.The input levels to the master effects are set by the
Send 1, 2 levels (step 3 or 9). If Send 1, 2 are zero,
the master effects will not apply. Send 1
corresponds to MFX1, and Send 2 corresponds to
MFX2.
12.Access the Prog P9: MFX/TFX– Routing page.
13.In MFX1 and MFX2, select the type of each master
effect.
The procedure is the same as when selecting an
insertion effect (see step 6).
Note:
You can only select a double-size effect for
MFX1. For details, please see “Double-size effects” on
page 70.
14.Press the On/Off button to turn on the master
effect.
Each time you press this button, the master effect will
toggle on/off. When Off, the output of the master
effect will be muted.
15.Use Return 1 and Return 2 to adjust the output
levels of the master effects.
Note:
For each effect, the Wet value of the Wet/Dry
parameter is the output level of the effect. The return
value is multiplied with this (“Return” = 127 will be
x1.0) to determine the actual output level of the master
effect.
16.Select the MFX1 and MFX2 pages, and set the
parameters for each selected effect.
For details on the “Program Effects settings” step 10.
Total Effect
17.If you use Bus (IFX/Output) Select to choose L/R
as the oscillator output, or if you set the post-IFX
Bus to L/R, the signal will be input to the total
effect.
The output from the master effects is input to the total
effect via the Return 1 and Return 2 settings of the Prog
P9: MFX/TFX– Routing page.
After being processed through the total effect, the
signal is output from the AUDIO OUTPUT L/MONO
and R outputs.
18.Access the Prog P9: MFX/TFX– Routing page.
19.Choose the desired total effect for TFX. The
procedure is the same as when selecting an insert
effect. (See step 6)
You can’t use a double-size effect as the total effect.
P (Effect Preset)
Effect Parameters
Effect On/Off
Wet/Dry
Summary of Contents for EASYSTART M50
Page 1: ...3 E Owner s Manual ...
Page 84: ...Arpeggiator function 78 ...
Page 88: ...Drum Track function 82 ...
