Routing effect settings Using effects in Combinations and Songs
71
Program
Combination
Sequencer
Effect
Arpeggio
Drum Track
Global
Media
For details, please see “Double-size effects” on page 70.
20.Press the On/Off button to turn the total effect on.
The total effect will toggle on/off each time you press
the button. If this is Off, the result will be the same as if
000: No Effect is selected. The input sound will be
output without being processed by the total effect.
21.Access the TFX page, and edit the parameters of
each effect to adjust the final sound as desired.
For details on the “Program Effects settings”, see step
10.
Using effects in Combinations
and Songs
In Combination, and Sequencer modes, you can
specify the routing of each timbre/track to the insert
effects, master effects and total effect. These settings
are made in the same way in each of these modes. We
will be using the example of Combination mode in our
explanation here.
Routing
1. Access the Combi P8–1: IFX– Routing1 T01–08
page.
2. Use “Bus (IFX/Output) Select” to specify the bus
to which each timbre will be output. Choose IFX1
if you want to send the output of a timbre to insert
effect 1.
The routing, insert effects, and chain settings are
shown graphically in the upper part of the page. In this
example, T01 (timbre 1) uses IFX1 and 2. T02 uses IFX2,
T03 uses IFX3 and 4, T02 and T05 use IFX4, and T06
and T07 use IFX5.
3. Use Send1 and Send2 to specify the send level of
each timbre to the master effects.
This can be set only if Bus (IFX/Output) Select is set to
L/R or Off.
Note:
The actual send level is determined by
multiplying this by the Send 1 or Send 2 settings for
oscillators 1 and 2 within the program selected by the
timbre. If the program parameter Send 1 or Send 2 is
set to 0, the resulting level will still be 0 even if you
raise this send level.
If Bus (IFX/Output) Select is set to IFX1–5, the send
levels to the master effects are set by Send1 and Send2
(Insert FX Setup page) following the insert effects.
4. Access the Combi P8–2: IFX– Routing2 page.
Bus (IFX/Output) Select
is the same as in the Routing 1
page. You can set it from either page.
FX Ctrl
sends the output of the timbre to an FX Control
bus. Use this when you want the audio input to an
effect to be controlled by another sound. There are two
FX Control buses, which gives you a great deal of
freedom for controlling effects freely. For details,
please see “FX Control Buses” on page 274 of the
Parameter Guide.
Insert effects
5. Access the Combi P8–1: IFX– Insert FX Setup page.
6. Select an insert effect in IFX1–5 and edit the
settings.
7. Access the IFX1–5 pages to edit the individual
effect parameters.
These settings can be made in the same way as in
“Program Effects settings” on page 69.
You can use MIDI to control dynamic modulation
(Dmod) for each effect, the post-IFX pan (CC#8),
and Send 1 and Send 2 levels.
An asterisk “*” is shown at the right of Ch01–Ch16
for the channel number of tracks routed to IFX. If
you’ve routed multiple tracks that have different
MIDI channel settings, this specifies the channel
on which they will be controlled.
Master effects and Total effect
These settings can be made in the same way as on
page 70.
You can control these effects via MIDI on the “Ctrl
Ch.” The specified MIDI channel will control
dynamic modulation (Dmod) for the Master and
Total Effect.
Summary of Contents for EASYSTART M50
Page 1: ...3 E Owner s Manual ...
Page 84: ...Arpeggiator function 78 ...
Page 88: ...Drum Track function 82 ...
