274
Effects
Modulation and Pitch Shift (Mod./P.Shift)
value for the Feedback parameter, the pitch will be raised (or
lowered) more and more each time feedback is repeated.
If
Feedback Position
is set to
Post
, the feedback signal will not
pass through the pitch shifter again. Even if you specify a higher
value for the
Feedback
parameter, the pitch-shifted sound will
be repeated at the same pitch.
52: Pitch Shifter BPM
This pitch shifter enables you to set the delay time to match the
song tempo.
d: BPM
e: Delay Base Note
e: Times
The delay time is the duration of “Times” number of “Delay Base
Note” note values at the “BPM” tempo (or if “BPM” is set to
MIDI, the tempo determined by MIDI Clock).
d: Time Over?
You can set the delay time up to 5,290msec. If the delay time
exceeds this limit, the error message “OVER!” appears on the
display. Set the delay time parameters so that this message will
not appear. “Time Over?” is only a display parameter.
53: Pitch Shift Mod.
(Pitch Shift Modulation)
This effect modulates the detuned pitch shift amount using an
LFO, adding a clear spread and width to the sound by panning
the effect sound and dry sound to the left and right. This is espe-
cially effective when the effect sound and dry sound output from
stereo speakers are mixed.
a: Pitch Shift [cents]
e: Depth
These parameters set the amount of pitch shift and amount of
modulation by means of the LFO.
g: Pan
h: Wet/Dry
The Pan parameter pans the effect sound and dry sound to the
left and right. With L, the effect sound is panned left, and the dry
sound is panned right. With a Wet/Dry = Wet setting, the effect
and dry sound will be output in a proportion of 1:1.
a
Mode
Slow, Medium,
Fast
Switches Pitch Shifter mode
b
Pitch Shift [1/
2tone]
–24...+24
Sets the pitch shift amount in steps
of a semitone
Src
Off...Tempo
Selects the modulation source of
pitch shift amount
Amt
–24...+24
Sets the modulation amount of
pitch shift amount
c
Fine [cents]
–100...+100
Sets the pitch shift amount in steps
of one cent
Amt
–100...+100
Sets the modulation amount of
pitch shift amount
d
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Time Over?
---, OVER!
Displays an error message when the
delay time exceeds the upper limit
e
Delay Base
Note
r...w
Selects the type of notes to specify
the delay time
Times
x1...x32
Sets the number of notes to specify
the delay time
f
Feedback
Position
Pre, Post
Switches the feedback
connection
g
Feedback
–100...+100
Sets the feedback amount
High Damp [%] 0...100
Sets the damping amount in the
high range
h
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src
Off...Tempo
Selects the modulation source for
the input level
i
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src
Off...Tempo
Table , “Dynamic Modulation
sources,” on page 243
Amt
–100...+100
Amount of modulation source
BPM
BPM
Base Note x Times
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Input Level
Input Level
+
High Damp
Delay
Feedback
Pitch Shifter
Feedback Position
Pre
Post
Tempo
a
Pitch Shift
[cents]
–100...+100
Sets the pitch difference from the
input signal
b
LFO Waveform
Triangle,
Square
Selects the LFO Waveform
c
LFO Frequency
[Hz]
0.02...20.00
Sets the speed of the LFO
Src
Off...Tempo
Selects a modulation source for LFO
speed
Amt
–20.00...
+20.00
Sets the modulation amount of LFO
speed
d
MIDI Sync
Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note
r...w
Selects the type of notes that
specify the LFO speed
Times
x1...x32
Sets the number of notes that
specify the LFO speed
e
Depth
–100...+100
Sets the LFO modulation depth for
pitch shift amount
Src
Off...Tempo
Selects the modulation source of
the depth of modulation
Amt
–100...+100
Sets the modulation amount of the
depth of modulation
f
Pan
L, 1 : 99...99 : 1,
R
Sets the panning effect sound and
dry sound separately
g
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src
Off...Tempo
Table , “Dynamic Modulation
sources,” on page 243
Amt
–100...+100
Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
LFO: Tri / Sqr
Pan
+
Pitch Shifter
Pitch
Higher
Pitch Shift Mod - Pitch Shift / Depth
Lower
Original Pitch
Pitch Shift (+ value)
LFO Waveform=Triangle
Depth (+value)
LFO Waveform=Square
Depth (–value)
Summary of Contents for PA 600 QT
