285
Effects
Delay
Appe
ndix
70: Tape Echo BPM
This is a tape echo that lets you synchronize the delay time to the
tempo of the song.
a: Tap1 Dmod Src
b: Tap1 Delay Note
b: Times
c: Tap1 Dmod Note
c: Times
If “Tap1 Dmod Src” is Off or the selected modulation is at 0, the
delay time will be the length specified by “Tap1 Delay Note” and
“Times.”
If “Tap1 Dmod Src” is other than Off, the delay time will change
so that it will be as specified by “Tap1 Dmod Note” and “Times”
when the maximum modulation is reached.
b: Time Over?
You can set the delay time up to 5,400msec. If the delay time
exceeds this limit, the error message “OVER!” appears in the dis-
play. Set the delay time parameters so that this message will not
appear. “Time Over?” is only a display parameter.
a
BPM (Delay)
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Tap1 Dmod Src Off...Tempo
Selects the modulation source of
the delay time
b
Tap1 Delay
Note
r...w
Selects the type of notes to specify
the delay time (tap1)
Times
x1...x32
Sets the number of notes to specify
the delay time (tap1)
Time Over?
---, OVER!
Displays an error message when the
delay time exceeds the upper limit
c
Tap1 Dmod
Note
r...w
Selects the note value used to
specify the delay time when the
modulation is at maximum
Times
x1...x32
Specifies the number of notes used
to specify the delay time when the
modulation is at maximum
d
Tap2 Position
[%]
0...100
Sets the position of Tap 2 relative to
the Tap 1 delay time the depth of
pitch variation
e
Tap3 Position
[%]
0...100
Sets the position of Tap 3 relative to
the Tap 1 delay time the depth of
pitch variation
f
Tap1 Level
0...100
Sets the Tap1 output level
Pan
L, 1...99, R
Sets the stereo image of tap1
FB Amt
–100...+100
Sets the Tap1 feedback amount
g
Tap2 Level
0...100
Sets the Tap2 output level
Pan
L, 1...99, R
Sets the stereo image of tap2
FB Amt
–100...+100
Sets the Tap2 feedback amount
h
Tap3 Level
0...100
Sets the Tap3 output level
Pan
L, 1...99, R
Sets the stereo image of tap3
FB Amt
–100...+100
Sets the Tap3 feedback amount
i
Feedback 0...100
Sets the amount of feedback for
Taps 1, 2, and 3
Src
Off...Tempo
Selects the modulation source of
feedback amount
Amt
–100...+100
Sets the depth by which feedback
amount will be modulated
j
High Damp [%] 0...100
Sets the damping amount in the
high range
Low Damp [%] 0...100
Sets the damping amount in the low
range
k
Saturation
0...100
Sets the distortion amount
l
Input Trim
0...100
Sets the input gain
Pre Tone
0...100
Sets the tone of the input
m
Wow Flutter
[Hz]
0.02...1.00
Sets the frequency at which pitch
variation will occur
Wow Flutter
depth
0...100
Sets the depth of pitch variation
n
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src
Off...Tempo
Table , “Dynamic Modulation
sources,” on page 243
Amt
–100...+100
Amount of modulation source
Wah Flatter
D
-mod
Tap2/3 Position
+
Tape
Saturation
Left
Right
FX Amt
Trim
Pan
Level
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Feedback
Feedback Amt
High / Low Damp
Pre Tone
Delay
(1)
(2)
(3)
Delay Time
BPM
BPM
Base Note x Times
Tempo
Summary of Contents for PA 600 QT
