21
4. Appendices
Pitch bend
This is a Pitch shifter that uses the pedal to control the pitch.
If you use this effect in a program where the MODULA-
TION effect block is on, the MODULATION effect block
will automatically be turned off.
PITCH BEND
“P BEND”
Knob 1 TIME
Adjusts the delay time.
Knob 2 FEEDBACK Adjusts the amount of feedback
(delay repeats).
Knob 3 PITCH
Adjusts the amount of pitch change.
Knob 4 FINE
Make fine adjustments to the amount of
pitch change.
Knob 5 MIX
Adjusts the mix amount of the effect. With
a setting of 10, only the effect sound will
be heard in the output.
Ring modulator
This effect multiplies the original sound with a sine wave to
produce bell-like effects. The cleanest results will be produced if
you use the neck pickup of your guitar, turn down the tone, and
pluck the string near the twelfth fret.
If you use this effect in a program where the MODULA-
TION effect block is on, the MODULATION effect block
will automatically be turned off.
RING MOD
“RINGMOD”
This is a ring modulator that lets you use the pedal to control
the frequency.
Knob 3 PITCH
Adjusts the tone when the pedal is
advanced.
Delay
These effects mix a time-delayed sound with the original sound
to add depth and spaciousness to the sound.
If you use this effect in a program where the AMBIENCE
effect block is on, the AMBIENCE effect block will
automatically be turned off.
HOLD DELAY
“HOLDDLY”
This will normally function as a delay, but when the pedal is
advanced all the way forward to press the switch, the pedal
LED will blink and the sound will be held (the delay sound
will continue to be heard). Since you can use the pedal to
control the input level to the delay, you can easily produce
special effects such as sound-on-sound. In Individual mode,
you can also hold by pressing program switch 2.
TAP DELAY
“TAP DLY”
When you advance the pedal forward and press the switch
twice, the tap tempo delay function will apply a delay at the
corresponding tempo. The pedal LED will temporarily go dark
the instant that the switch is pressed. The depth to which the
pedal is pressed will control the input level to the delay. In
Individual mode, you can also press program switch 2 twice to
specify the tempo.
Knob 1 TIME
Adjusts the delay time.
Knob 2 FEEDBACK Adjusts the feedback amount
(delay repeats).
Knob 3 TONE
Adjusts the tone of the effect sound.
Knob 4 ———
————
Knob 5 MIX
Adjusts the mix amount of the effect
sound.
Sample and play
If you use this effect in a program where the AMBIENCE
effect block is on, the AMBIENCE effect block will
automatically be turned off.
SAMPLE&PLAY
“S+PLAY”
This allows approximately 8 seconds of recording. By using the
reverse setting, you can produce special “scratch” effects.
1. Press the expression pedal all the way forward to enter
record-ready mode. The pedal LED will blink. In
Individual mode
, press program switch 2 to enter
record-ready mode.
2. Play a phrase etc. on your guitar. Recording will begin
automatically at the moment you start playing and the
pedal LED will begin blinking faster.
3. When the recording time specified by
TIME
has elapsed,
recording will end and the pedal LED will not be lit.
Also, you can stop recording before the specified
recording time has elapsed by pressing the pedal all the
way forward (i.e., pressing the pedal switch).
To re-do the recording, repeat the procedure from step 1.
During recording, you can also return the pedal and then
press it again to stop recording and begin playback.
4. Operate the expression pedal. When you advance the
pedal, the recorded phrase will playback. If you have set
REVERSE
to
A-1
...
A-4
or
b-1
...
b-4
, returning the pedal
will cause the sound to playback in reverse at the
specified speed.
If you set
REVERSE
to
OFF
, the sound will only
playback forward.
With a setting of
LP1
or
LP2
, advancing the pedal
forward will playback the sound as a repeating loop.
When you return the pedal back and then advance the
pedal again, playback will begin from the beginning.
Recording will not begin unless you play your guitar
louder than the threshold.
The recording sound will be erased when you enter
Phrase Trainer mode or when you turn off the power.
Knob 1 TIME
Specifies the sample time (recording time).
Knob 2 REVERSE OFF: When you press the pedal, the
sound will playback to the end and
then stop.
LP1: Press the pedal forward to playback
as a loop, and return the pedal
backward to stop.
LP2: Press the pedal forward to playback
as a loop, and return the pedal
backward to playback to the end and
then stop.
A-1...A-4: Press the pedal forward to playback,
and return the pedal backward
to playback in reverse.
b-1...b-4: Press the pedal forward to playback
from the beginning, and return the
pedal backward to playback in
reverse from the end.
Knob 3 ———
————
Knob 4 ———
————
Knob 5 MIX
Adjusts the output level of the sampled
sound.
